Fogger V4!!

Status
Not open for further replies.

dynoman2002

Senior Member
Sep 4, 2014
161
139
California
Also looks like they shortened the deck to accommodate for the bigger chimney to fit those ugly ... post pins. The rep said the v5 juice capacity was the same as 4.1 and the overall dimensions also. Looks like from the picture theres only 2 threads for the chimney to catch on. Idk have to wait and see might be a dream come true but Im not holding my breath.
 

DejayRezme

Super Member
ECF Veteran
  • Mar 22, 2014
    910
    523
    Europe
    I, myself, don't like spring loaded connections. I find them unreliable. I'd rather have screws holding my wires firmly.
    Also, I don't see an O-Ring seal between the Top Filling Cover and the Top Cap. That, to me means no vacuum action.

    I *think* I saw a fat o ring between the top cap on one picture. But I have to agree about the spring loaded posts. Someone mentioned somewhere that they ordered a special version of the V5 with screws instead of springs. Maybe the Fogger V5 thread.

    Also, I got around to try to clean my Big Fogger again. After another UC bath I used my new pipe cleaners on it and damn there is a lot of dirt in there. No wonder it tastes like an exhaust pipe. I still haven't got it cleaned and I'm almost outraged by this level of dirtyness and bad QC for the Big Fogger. After having it soak for more than a week in water some rusty stuff came out of the base but I think it's the shrapness or whatever is in those airholes. Not sure if I'll ever get it cleaned so it doesn't taste while drawing air.
     

    AMDTrucking

    Ultra Member
    ECF Veteran
    Dec 7, 2013
    1,950
    3,232
    California
    Last edited:

    SlickWilly

    Tinkerer
    ECF Veteran
    Verified Member
    Feb 18, 2013
    1,275
    20,835
    NY

    AMDTrucking

    Ultra Member
    ECF Veteran
    Dec 7, 2013
    1,950
    3,232
    California

    b.m.

    Vaping Master
    ECF Veteran
    Verified Member
    Mar 30, 2014
    6,739
    21,015
    51
    Ohio
    On that big Orchid,

    Forgive me please, but do you really like the single Airflow hole in the middle instead of dual? And do you like a single Positive nut instead of dual screw post?

    You couldn't be serious :confused:
    Ok,i stand corrected.I was on my phone when i seen that pic,and didn't notice those differences.The only difference i had noticed was the clearer looking tank section and the 2 piece chimney.Now that i can see the picture bigger,that thing should not even be called an orchid,other than the symbol on the chimney,it's not even close.That single air hole,and only having 2 posts instead of the tri-post that the smaller one has,it looks like there wouldn't be a way to get dual coils over the air hole either,i could be wrong,but i dont see how you would do it.
     

    AMDTrucking

    Ultra Member
    ECF Veteran
    Dec 7, 2013
    1,950
    3,232
    California
    If you guys think FastTech shipping is slow, compare it to FocalEcig shipping:

    Z0xhwF4.jpg
     

    DejayRezme

    Super Member
    ECF Veteran
  • Mar 22, 2014
    910
    523
    Europe
    OK, so now I'm an RTA/RBA junkie but I really don't like the idea of a dripper, too much trouble to keep dripping.

    If you want to try a dual coil dripper similar to the Fogger try the Magma RDA (Infinite clone is great) it has vertical air channels and about 1ml capacity drip well. Build and wicking is easier. I'm on the fence if my Fogger or my Magma tastes better though. You should check out the magma thread though.


    I thought recently that my Fogger V4 actually tasted better than my Magma, but ever since I messed up a juice recipie (90% PG? 30mg nic? Something went terribly wrong!) I don't like the taste of my Fogger anymore. I figure it must be the build though.
     
    Status
    Not open for further replies.

    Users who are viewing this thread