Genesis Line LV Assembly Instructions

[drewbalicious]

So here's the deal. I purchased an un-assembled Genesis Line LV from another member on the classifieds. He was gracious enough to send me the assembly instructions, then in a moment of haste I deleted the message along with the instructions.

I just recently re-sold the un-assembled Genesis to another member on the classifieds and I am on the hunt for the assembly instructions for him. I cannot seem to find them anywhere. I sent a PM to the member who I believe creates the Line series asking if he might have them but no word back yet.

So I'm posting here in hopes that another gracious member out there would happen to have them. Any help or guidance in the right direction is extremely appreciated. Thanks in advance.

-Drew-

 

[tybin]

HI Drew. I'm not sure what you mean by assembly instructions? if you go to vaporwall, you can pm Dellboy over there and he can get you set up

 

[drewbalicious]

When I say assembly, I mean how to put it all together. I received it completely disassembled. Literally every single piece on it is separate and needs to be hot glued together and what have you. It was a task I wasn't willing to undertake so I sold it to a member that hopefully is.

But I truly appreciate the guidance Tybin. I'll have to hop on over to vaporwall and get all registered up so I can bug Dellboy about it. Is he the creator of the Genesis Line, or just a member than knows a crap ton about them?

 

[BJ43]

When I say assembly, I mean how to put it all together. I received it completely disassembled. Literally every single piece on it is separate and needs to be hot glued together and what have you. It was a task I wasn't willing to undertake so I sold it to a member that hopefully is.

But I truly appreciate the guidance Tybin. I'll have to hop on over to vaporwall and get all registered up so I can bug Dellboy about it. Is he the creator of the Genesis Line, or just a member than knows a crap ton about them?

Search for a thread by Dan on how to take apart and repair a leaking Line. I have 4 and have taken them apart to replace the PTFE. Used his pics to do mine.

http://www.e-cigarette-forum.com/fo...-complete-disassembly-fix-12.html#post4700687

 

[drewbalicious]

Thank you everyone for everything. But the member I bought it from managed to get his hands on the original assembly guide. Thanks again, I love the ECF!

 

[Robert T]

The Line and the Genesis LV are different attys. If you need the LV build instructions they're here:

http://board-projekte.de/download/assembly-genisis-lv-IV.pdf

 

[drewbalicious]

Thank you so much Robert. Those are the exact ones I was looking for!

 

[Robert T]

No problem, Drew.

 

[WNCmotard]

Thanks guys, I appreciate it too, I'm the one that ended up with it. I have an issue though, I wired up my 510 connector, hot to center post, ground to the outside, and I have nothing when I wire up a coil. I think possibly one of the small brass terminals is touching the body internally. Other thoughts? (I did oxidize the wick, and kanthal wire properly according to videos on youtube.)

 

[Robert T]

If you have a DMM check at the screw terminals for cont. Outside of connector to the short post, inside of connector to tall post. My DMM beeps if you have cont. If yours doesn't have that then put it on ohms and you should get a reading. If every thing is right there check the voltage at the post. That's somewhere to start.

 

[WNCmotard]

Thanks Robert, that's how I had it wired. Unfortunately, I tore into it last night to solve the issue, and lost one of the tiny brass soldering tabs and one of the plastic washers. This thing is a PITA, I'm really glad my DID shipped. I'll chalk this one up to a noob learning experience of what not to do.

 

[Robert T]

Thanks Robert, that's how I had it wired. Unfortunately, I tore into it last night to solve the issue, and lost one of the tiny brass soldering tabs and one of the plastic washers. This thing is a PITA, I'm really glad my DID shipped. I'll chalk this one up to a noob learning experience of what not to do.

I wouldn't give up yet! You should contact lorderos33 in a PM and see if he knows where to get parts or he might be willing to assemble it for you. As another option, I could l could look up Tai Pan's email address for you and you could ask him about spare parts. He ran the CoOp for the genesis LV. Let me know.

 

[WNCmotard]

I wouldn't give up yet! You should contact lorderos33 in a PM and see if he knows where to get parts or he might be willing to assemble it for you. As another option, I could l could look up Tai Pan's email address for you and you could ask him about spare parts. He ran the CoOp for the genesis LV. Let me know.

Yeah, I would really appreciate that Robert. I'll gladly give it another go if I can find parts for it, as I do like to tinker with things. I'll look up lorderos33 and shoot him a PM as well. I'm one of those guys that usually orders extra parts for something if possible, just for this reason.