Ggts

[RiverNut]

Get sealed unless you plan on using it with a bottom feed mod. Sorry, that's about the only question I can answer

 

[LongDraw]

Thanks River.

I bought one from empiremods, but it is unsealed. I took a guess, figured the unsealed would allow the juice to get sucked back up from the collector tank.

If the bottom is sealed how does juice get back in? Will the unsealed I bought work for now?

Get sealed unless you plan on using it with a bottom feed mod. Sorry, that's about the only question I can answer

 

[RiverNut]

actually, I was wrong lol. Yes, since you'll have the collector tank, the unsealed one is the one you want.

 

[LongDraw]

So this was unfortunate.

I was pulling out the adjustable center post pin and accidentally pulled it out. No biggie I thought, I would put it all back together. I unscrewed the center post nut, then pushed the orings out. When I went to put the orings back on the center post one broke, man that sucked cause I don't have any small enough.

Well I also can't seem to unscrew the black center post stop. So for now I put center post nut on the center post, put the one oring back on and then pushed this back into the center post stop.

This is working, but is this safe? I don't think the oring went into the center post stop. Also, how do you guys unscrew the black center post stop?

Gonna take stock of what orings I have and need for back ups and put in an order.

 

[justinred]

Wear rubber gloves. Apply pressure using fingertip on the delrin and twist counterclockwise.

 

[yankeebobo]

Gloves on delrin. Gentle pressure on nut. It'll come apart. It's safe. No worries.

 

[LongDraw]

Sounds good. Thank you.

Also, I am checking oring sizes. The stick on the gg forum says 15 x 1.5 for both the ody and ggts but the gg wicki says 16 x 1.5 for those, anybody know for sure?

Wear rubber gloves. Apply pressure using fingertip on the delrin and twist counterclockwise.

 

[LongDraw]

Thanks yankee. I was just wanted to make sure that the way it is set up now, only 1 oring and I don't think it is inisde the delrin, would work till I get my new orings in. Don't even want to try and take out the delrin now for fear of breaking that other oring.

Gloves on delrin. Gentle pressure on nut. It'll come apart. It's safe. No worries.

 

[LongDraw]

Sorry, last question.

Any good suggestions for where to get orings, and what should the material be? The bookmark I had changed now.

I had bought from orings usa before and they were good just high shipping. I had seen another sight mentioned but can't find the book mark.

 

[yankeebobo]

When you pull it apart you assemble the whole thing minus the delrin, slip the tiny orings onto the post and then put delrin on. Easier than trying to stuff orings back in.

Sent you email.

 

[fright88]

I've used 1 o'ring there before and it was no problem. As for size pretty sure it is a 2x1 if I recall correctly for the center post.

 

[yankeebobo]

Yup. 2x1. Tiny damn thing. Don't drop it.

 

[LongDraw]

Thanks yankee, that was super helpful.

So I am gonna order the 2x1, any others that would be good to have on hand right now? Figure since can only order in packs of 100 gonna just order a couple here and there. Wasn't sure if some orings get used up faster

 

[yankeebobo]

The TS utilizes orings economically. I don't find needing to replace those often. Maybe the CT base if you take it off often to clean.
The ithaka I have stock in the oring company.

 

[LongDraw]

Haha, sounds good.

The TS utilizes orings economically. I don't find needing to replace those often.
The ithaka I have stock in the oring company.