Goblin Mini RTA review.

[Mr. Underhill]

I got my new Lightning Vapes drip tip for the GMini in yesterday, It's so nice to not have to use the 510 adapter. I hope Youde fixes the drip tip and adds top fill to the v2 down the road. Any who here's my current setup with the GMini. It's a 26 gauge .14 dual Ti build, and It vapes stupendously! Flavor is amazing. It's set at 480f at 27j on my SX350j mod.

 

[ThunderDan]

Very nice. I may have to bite the bullet and order one myself.

 

[Mooch]

Loving mine on a Tesla Two with Spectrum tanks glass!

 

[Two_Bears]

I got my new Lightning Vapes drip tip for the GMini in yesterday, It's so nice to not have to use the 510 adapter. I Hope Youde fixes the the drip tip and adds top fill to the v2 down the road. Any who here's my current setup with the GMini. It's a 26 gauge .14 dual Ti build, and It vapes stupendously! Flavor is amazing. It's set at 480f at 27j on my SX350j mod.
View attachment 492880

Nice setup there.

Yes the Gmini has incredible flavor. I never expected that little tank to have better flavor than some of the larger RDAs. But IT DOES. You can pick up a clone for $11-20.

 

[Two_Bears]

Very nice. I may have to bite the bullet and order one myself.

I would recommend it. fasttech has clones for $9-11 you can get an authentic at Fasttech for, $25 or so

 

[ThunderDan]

I would recommend it. fasttech has clones for $9-11 you can get an authentic at Fasttech for, $25 or so

I meant the Lightning Vapes drip tip, should have been more specific. I have two Goblin minis that I adore, so I might as well pick up some custom drip tips for them.

 

[Nailz]

Got my Goblin mini from sweet-vapes yesterday, so far I am really liking it, my only real complaint so far, when will these atty manufacturers make sure the post screws don't cut your leads, that is really annoying, tighten down 1st coil and post screw just cuts through it

After that I was more gentle, was going to dremel the screws, but they are so tiny, concerned I would loose them, and only got 1 extra in spares bag.

Did a single build to start with, wasn't bad vape, but nothing special, so went and added another coil and then it was rocking, using 26 gauge, 6 wraps around 2.5mm rod, coming in at 0.40ohms, with the deck being so small, need very little wick with this thing, but am happy straight out, getting a good vape with no dry hits or leaking, was concerned might leak when refilled, but nope not a drop.

 

[Two_Bears]

Got my Goblin mini from sweet-vapes yesterday, so far I am really liking it, my only real complaint so far, when will these atty manufacturers make sure the post screws don't cut your leads, that is really annoying, tighten down 1st coil and post screw just cuts through it

After that I was more gentle, was going to dremel the screws, but they are so tiny, concerned I would loose them, and only got 1 extra in spares bag.

Did a single build to start with, wasn't bad vape, but nothing special, so went and added another coil and then it was rocking, using 26 gauge, 6 wraps around 2.5mm rod, coming in at 0.40ohms, with the deck being so small, need very little wick with this thing, but am happy straight out, getting a good vape with no dry hits or leaking, was concerned might leak when refilled, but nope not a drop.

Never had a cut wire or leaked a drop.

I LOVE the little Beastie.

 

[Two_Bears]

I meant the Lightning Vapes drip tip, should have been more specific. I have two Goblin minis that I adore, so I might as well pick up some custom drip tips for them.

Sorry brother. Thought you were talking about the atty.

 

[Ou2mame]

I rubbed the screws on a nail file and they aren't cutting my coils anymore. Or switch to 26g. I only had a problem with 28g.

 

[roxynoodle]

More often than not I sand the bottoms of screws when I get a new atty.

Still considering a Gob Mini for my collection.

 

[ThunderDan]

More often than not I sand the bottoms of screws when I get a new atty.

Still considering a Gob Mini for my collection.

You should stop considering, and nab one. If you want a shorty tank with bottom fill that is.

I'll trade you one of mine, for one of your rdtas.

 

[Nailz]

More often than not I sand the bottoms of screws when I get a new atty.

Still considering a Gob Mini for my collection.

You should get one, easy tank to work with, and being short, it is good on flavor, had no problems with dry hits or leaking at all, touch wood

 

[TheWestPole]

You should get one, easy tank to work with, and being short, it is good on flavor, had no problems with dry hits or leaking at all, touch wood

@Nailz, I am getting a little leaking out the air holes (I assume). Are you putting any of the wick ends down into the juice channels?

 

[Nailz]

@Nailz, I am getting a little leaking out the air holes (I assume). Are you putting any of the wick ends down into the juice channels?

Yes but just a small amount, enough to suck up the juice, but not enough to block it, I wick it the same as I do with any of these sort of atties, the billow 2, aqua v2 etc

 

[roxynoodle]

Got the second to last at Smog. $13 with shipping.

 

[Nailz]

Got the second to last at Smog. $13 with shipping.

Damn good deal @roxynoodle paid $28 after shipping, so you scored

 

[roxynoodle]

Sometimes it pays to wait

 

[ThunderDan]

Yeah I had to nab one myself at that price. Makes it 3 goblins minis for a total of $39 (first one was $26, 2nd one free, 3rd one $13).

I remember my OG gobin was $32 shipped back in January.

 

[TheWestPole]

Yes but just a small amount, enough to suck up the juice, but not enough to block it, I wick it the same as I do with any of these sort of atties, the billow 2, aqua v2 etc

Well, I'll try again. Wicked the same as with Orchid, Goblin, Silverplay, Cthulhu. Maybe a bit too short with the wicks.