- Status
OK, followed everbodys tips(Mostly) and have my ASH up and running. But I do get this like slight metallic taste when vaping. Anything I can do for that?
the draw is way to airy for me, but the tight draw caps are out of stock on HoH, any ideas on a temporary fix for that?
Other than those thing I am very happy with it
the draw is way to airy for me, but the tight draw caps are out of stock on HoH, any ideas on a temporary fix for that?
Other than those thing I am very happy with it
OK, followed everbodys tips(Mostly) and have my ASH up and running. But I do get this like slight metallic taste when vaping. Anything I can do for that?
the draw is way to airy for me, but the tight draw caps are out of stock on HoH, any ideas on a temporary fix for that?
congratulations!!!
the slight metallic taste will go. If your coils are 101 percent perfect it takes a very short time if not a little longer
concerning the draw:
I found this information don't remember who is came from I think it was Ob:
Tips on making a smaller air hole:
here is that modification that Zen~ mentioned recently. I did this because I personally prefer a stiffer draw and have read that there are others who also prefer this so I wrote up how I tightened the draw on my Zenisis in case anyone else wants to do the same. He went over alot of what this does and the possible risks in his post so I'll just get right to it then
You need a dremel with a grinding cutoff wheel, an 18 ga needle, a VERY TINY drop of super glue, a fine pointed prescision file and a standard Zenisis cap.
What you need to do is use the dremel to cut a 1/8" piece off the needle. Use the file to make sure the ends of the piece you just cut are clear and to hold this tiny piece of needle securely.
Test fit the needle piece to the Zenesis cap. It should fit right in the hole with almost no play, but not snug. If it fits as mentioned, you're ready to set it in place.
Take the tiniest drop of superglue and put it on the outside of the needle you just cut off, being careful not to get any on the file.
Put the glue covered needle into the air inlet on the Zenisis cap till it is flush with the outside of the cap and hold it there for 5-10 seconds. The glue should set almost immediately.
Now pull the file back out of the glued together parts and put the cap back on the Zenisis.
Give your Zenisis a test vape. If you did everything right it will now have a tighter yet comfortable draw and should create a nice vaccum in the vapor chamber that will prevent dry and harsh hits.
If you decide to try this, please be careful not to damage the finish on your Zenesis by using too much glue. Remember, less is more in this situation.
Good morning emonty, Mrephunk and Murdock. Ash and AYS doing fine...I know everyone was concerned
Now, if I could find a way to make money without actually working
Now, if I could find a way to make money without actually working
Now, if I could find a way to make money without actually working
When you figure that out please shoot me a pm with instructions
And thanks for the info emonty and thanks for the orings got those yesterday with my ASH. Mightiest deal with the draw till I can get a stiff draw cap. I am worried I will use to much glue
《Sent from my handheld information procuring fruit ninja》
Last edited:
Blackwater:
concerning the topcap being loose: be sure you use the big(gger) oring as it could be that they are swapped.
concerning the topcap being loose: be sure you use the big(gger) oring as it could be that they are swapped.
When you figure that out please shoot me a pm with instructions
And thanks for the info emonty and thanks for the orings got those yesterday with my ASH. Mightiest deal with the draw till I can get a stiff draw cap. I am worried I will use to much glue
《Sent from my handheld information procuring fruit ninja》
I'll do that..LOL
Good Morning Zenfidels and Ian74, ksmith,BradsBrotherStu! 
Not sure why the hell I'm up this early and I went to bed around 2:20 am.
I guess I'm anxious to pick up my baby "Crazy Lu" who's been boarded since I left for Buffalo.
I miss her so and sadly I miss rat & Lee, "Padre Jfro" and K-man and Manel{ I'm sure the spelling is wrong}
and everyone else I got to spend a 'lil time with at Mr. Ratty's Bar & Grill. lol
I'm such a sentimental sap!
C.B.
Not sure why the hell I'm up this early and I went to bed around 2:20 am.
I guess I'm anxious to pick up my baby "Crazy Lu" who's been boarded since I left for Buffalo.
I miss her so and sadly I miss rat & Lee, "Padre Jfro" and K-man and Manel{ I'm sure the spelling is wrong}
and everyone else I got to spend a 'lil time with at Mr. Ratty's Bar & Grill. lol
I'm such a sentimental sap!
C.B.
Last edited:
Did he put that on there, or did you? 
OK, this had me chuckling much longer than it should have.
I envisioned Zen~ chuckling to himself putting it together, going "Heh. Here's your damn Boomstick! Now quit asking about it!"
It is, indeed, evidence of Zen~s awesomeness.
-Insp. 2211
I have a very important question. I am now the proud owner of a ZAP. Am I a Zenfidel or just a Zeni??? 
I have a very important question. I am now the proud owner of a ZAP. Am I a Zenfidel or just a Zeni???
LOL... Being a Zenfidel has nothing to do with anything you own.
Ain't that the truth, but except in the case of emonty, he was so whiny and pathetic about not being able to have one we just sympathized and let him tag along.
I have a very important question. I am now the proud owner of a ZAP. Am I a Zenfidel or just a Zeni???
Being a Zenfidel has nothing to do with owning a Zenesis, it is a state of mind and how you help others.
I have a very important question. I am now the proud owner of a ZAP. Am I a Zenfidel or just a Zeni???
Welcome to the family, Mookie
OK, followed everbodys tips(Mostly) and have my ASH up and running. But I do get this like slight metallic taste when vaping. Anything I can do for that?
the draw is way to airy for me, but the tight draw caps are out of stock on HoH, any ideas on a temporary fix for that?
I snipped off a tiny piece of the #400 wick and stuffed it in the air hole. That worked long enough for me to decide airy is better :
:- Status
Similar threads
- Locked
