Hungarian NGP Genesis PV

[Aron Gatt]

What you mean turbo? I don't know if I'm understanding you well .. But my wick is almost the same size as the wick hole and with no center hole .. Which is wicking great and I use a 70/30 VG-pg mix ... No trouble with top cap .. Since I have a twisted coil ,I am getting warmer vapor and no issues ..

 

[Turbo]

What you mean turbo? I don't know if I'm understanding you well .. But my wick is almost the same size as the wick hole and with no center hole .. Which is wicking great and I use a 70/30 VG-pg mix ... No trouble with top cap .. Since I have a twisted coil ,I am getting warmer vapor and no issues ..

I was referring to the starting dimensions of the mesh before rolling; 40x30mm, 50x40, etc. The original had space around the wick. I was thinking they did it that way to avoid the wick touching the sides in case it were to get hot and melt the plastic around it.

I guess I can just measure the mesh they gave when I need to roll another, just thought to poll the users here until.

 

[Aron Gatt]

I was referring to the starting dimensions of the mesh before rolling; 40x30mm, 50x40, etc. The original had space around the wick. I was thinking they did it that way to avoid the wick touching the sides in case it were to get hot and melt the plastic around it.

I guess I can just measure the mesh they gave when I need to roll another, just thought to poll the users here until.

ok .. Mine is 30/40 mm and its very very close to the tank .. I can turn it but almost can't see the little gap ... I didn't have melting issues yet " but then if some one has encountered this issue pls tell us..

 

[jun0felix]

no melting issues here - there's too much juice around the hole, and i like fat wicks 45 - 50 mm

 

[martinc]

I`ve seen it mentioned,I think by the one that has a youtube review about the 4.1

 

[Turbo]

Well I just unrolled my original NGP wick as it was acting up and made a new one. The dimensions of it are 35mmx40mm (length/width) for what it's worth.

 

[Mazlee]

Hi boys

a further user are here

 

[JollyRogers]

Hey ya Mazlee Welcome! I am on the Hungarian E-cig forum also!

 

[Mazlee]

your name is the same there as well?

 

[JollyRogers]

It is the same there as well I have 2 NGPs, both ring switches, one is a prototype pop on tank held with an o-ring, and the other is a standard screw down top. Both are the standard aluminum... Wish I had an anodized one though

 

[Pega]

Just a quick note from the NGP team that they asked me to jot down for you here. Be careful when making purchases for second hand NGPs on the classified's always check that they have been restored by NGP before being resold. The NGP guys are not able to honor warranties for NGPs that are re-sold by people here that purchased them in the Hungarian classifieds. Your best bet is to purchase them directly from the NGP guys at info@ngp.hu.

If you have any issues you can contact me and time permitting I will do my best to help you out (I am only translating to help them out sometimes).

 

[YoureFired]

Is there still a several week waiting period to get an NGP Touch? Anyone know? Also, I just checked the site and didn't see an option to order a black NGP. Thanks

 

[ChrisEU]

Ah, the NGP is a great device. I have a silver anodized Touch version and just breaking in a setup I would like to share with you:

I am using a 500 mesh with 37 x 75 mm (37 is the length into the tank with a bit of reservoir above the coil, 75mm is needed for a solid wick), once heated before rolling and oxidized under the coil only. I use AWG 29 Kanthal A - 6 coils, measuring 1.3 ohms. Batteries are 18350 AW IMR and Sony US18650V

This setup is able to wick Bobas Bounty vertically and I love it. Which is wierd because I never liked Genisis style atties, I even sold a Cobra because I couldn't get it to wick properly.

The only issue I have with the setup is a delay of about half a second between firing and good vapor production - but I can deal with that.

So, if you have wicking problems, try to get hold of 500 mesh and AWG 28 or 29 Kanthal (0.30 or 0.35mm) and use a lot of it.

 

[jun0felix]

@Chris: there's this other thread collecting mesh dimensions: optimal-mesh-dimensions-wire-size-wraps-specific-devices

 

[ChrisEU]

Posted there - but I am sure this is not optimal, just good enough for me =)

 

[jun0felix]

yes the title of the thread is a bit optimistic

 

[Eagle Talon]

Just a quick note from the NGP team that they asked me to jot down for you here. Be careful when making purchases for second hand NGPs on the classified's always check that they have been restored by NGP before being resold. The NGP guys are not able to honor warranties for NGPs that are re-sold by people here that purchased them in the Hungarian classifieds. Your best bet is to purchase them directly from the NGP guys at info@ngp.hu.

If you have any issues you can contact me and time permitting I will do my best to help you out (I am only translating to help them out sometimes).

sorry dude! but:
used product warranty to give the seller! it has nothing to do with the manufacturer. this post therefore pointless!

 

[Pega]

New NGP version will go on sale today! Look for the list for new devices (Chrome, black anodized, aluminium tanks) later today on VaporWall:

www.vaporwall.com • Login

 

[Pega]

New NGPs:

NGP Push Button V3 (black anodized and chromed aluminum):

NGP Ring Switch V3 (chromed aluminum):

 

[Pega]

list is now live on vaporwall, limited stock ready to ship tomorrow

www.vaporwall.com • Login