Indulgence Mt-Rta
- Thread starter 98ruby
- Start date
- th_trl_thread_readers 0
- Status
thx, I had seen those, outta stock thoughi'm hoping someone has seen them somewhere else that I have yet to find in my search...
Slight tighter fit, but SubTank Mini orings will work fine, glass as well.
Origin vape has the black mutank and velocity decks in stock so I said what the heck. Grabbed them and a baggie of the colored o-rings, she's looking sharp ladies and gents, could be suprtrkr's long lost twin vape:
7 wrap 26/32 claptons at 3mm id fit with ease into the v-deck. Wicked her like the MT with a metric ton of rayon and we're off to the race. Broke the build in at 80 watts but it's running well at 100 now. I'm going to have to drop from 6mg to 3mg, I'm getting a little loopy.
7 wrap 26/32 claptons at 3mm id fit with ease into the v-deck. Wicked her like the MT with a metric ton of rayon and we're off to the race. Broke the build in at 80 watts but it's running well at 100 now. I'm going to have to drop from 6mg to 3mg, I'm getting a little loopy.
My black one is on my rx200, too.
Here's something that's kinda cool......
Found this in Petco today, it's a mat for pet bowls, nice laminated top and non skid back, thought it would make a cool build mat for 5 bucks......for this Star Wars geek anyway......to stay on topic I use it build my MT RTA [emoji1]
Sent from my iPhone using Tapatalk
Found this in Petco today, it's a mat for pet bowls, nice laminated top and non skid back, thought it would make a cool build mat for 5 bucks......for this Star Wars geek anyway......to stay on topic I use it build my MT RTA [emoji1]
Sent from my iPhone using Tapatalk
Ok, I finally got around to building the tank I bought by mistake, the Advken Ωega. I built it the same as the black MT: dual parallel 26ga, 3.5mm ID, .11 Ohms. I don't think I have gotten it wicked right. Hard to say, not through rayon break in, but I seem to taste a lot of wick; It may not be drawing.
![20160109_193700[1].jpg](https://www.e-cigarette-forum.com/attachments/20160109_193700-1-jpg.521332/ "20160109_193700[1].jpg")
I've been stuck on the parallel 28 ga you suggested, but I stepped it up just a hair tonight... I like it. 26/32 paralleled with straight 26 ga. .12 ohms.. It's like your parallel 28 build on crack
The Ωega seems to be wicking. I had the TCR for SS316 all borked up; that's probably why it was burning. Still, while the level in the tank is dropping, I haven 't yet caught it making bubbles. Too much wick, I'm thinking.
From looking at the deck, I would put just a short little bit of tail in the very beginning of each wick channel, just to that "shelf".
Concur, Roxy. I took it to the bottom of the holes. I think that's too much. When I vape it dry I'll break it and snip a bit.
I'm running the 101 alien clapton! 4wrap 2.5 id .17ohms! good flavor & clouds! gonna make next build a little higher!
I need to put my SS Clapton wire in the mutank and see how it does. My batteries are low and I can't get a build in without killing them so I'll do it first thing in the morning
Sent from my Nexus 6 using Tapatalk
Sent from my Nexus 6 using Tapatalk
Looks like there's more than enough room from the pics!! I don't leave that much room between my air inlet and the bottom of the coil. I shim it with a 1.5 mm Rod. It keeps it from getting harsh, imo. Nice coils!
- Status
