Indulgence Mt-Rta
- Thread starter 98ruby
- Start date
- th_trl_thread_readers 0
- Status
I've seen this come up a few times but no links are ever posted about itPsst...HIGO
Sent from my Nexus 6 using Tapatalk
Can you drop a link please? I'm on my phone and using tap a talk with this site is a disaster if I'm not subscribed to the thread
Sent from my Nexus 6 using Tapatalk
Sent from my Nexus 6 using Tapatalk
Sure thing
. Slightly less air than the MT, but the flavor is freaking insane.HIGO RDTA by Focusecig
You can count me out on that one, the design is awful. I'm talking about the outside looks of it, maybe if some stuff changes but as of what I saw, no way
Sent from my Nexus 6 using Tapatalk
Sent from my Nexus 6 using Tapatalk
Looks interesting. Ugly, but it's a prototype. More air would be nice, I'm thinking. So when can we get one to try?
For those of us using rayon to wick this beast, I get no leaks, flooding, dry hits, or leaking after filling at all with how I'm wicking it. Give this a try:
Start with the Scottish Roll wick style. Look it up if you're unaware of how it works. Basically, cut the length you want to use, separate the rayon with the grain as much as you possibly can (until it's practically falling apart), and then roll it up with the grain as tight as possible. Then roll it in your fingers to get it even tighter. Once done, pull it through your coils. There should be quite a bit of resistance, the wick should fit quite tightly. Now, don't thin the tails! I know that's contrary to rayon usage, but just don't do it! Use whatever tool you like to stuff the tails into the juice channels, leaving the remainder sticking out below the threading. Next, wet the wick at the coils, but not down the tails at all. Screw the chimney on, then cut the tails a few mm out from the chimney. Stuff what's left carefully back into the holes. Assemble, fill, wait a couple minutes for saturation, then chain vape that nasty rayon taste away for the next few minutes.
Now you're good to go! When refilling, make sure to shut the airholes first, remove the top, fill, screw the top on halfway, turn it upside down and screw it on the rest of the way, open the airflow, and inhale through the drip tip as you turn it back right side up.
I have had nothing but success doing it this way. Try it and let me know how it goes.
Start with the Scottish Roll wick style. Look it up if you're unaware of how it works. Basically, cut the length you want to use, separate the rayon with the grain as much as you possibly can (until it's practically falling apart), and then roll it up with the grain as tight as possible. Then roll it in your fingers to get it even tighter. Once done, pull it through your coils. There should be quite a bit of resistance, the wick should fit quite tightly. Now, don't thin the tails! I know that's contrary to rayon usage, but just don't do it! Use whatever tool you like to stuff the tails into the juice channels, leaving the remainder sticking out below the threading. Next, wet the wick at the coils, but not down the tails at all. Screw the chimney on, then cut the tails a few mm out from the chimney. Stuff what's left carefully back into the holes. Assemble, fill, wait a couple minutes for saturation, then chain vape that nasty rayon taste away for the next few minutes.
Now you're good to go! When refilling, make sure to shut the airholes first, remove the top, fill, screw the top on halfway, turn it upside down and screw it on the rest of the way, open the airflow, and inhale through the drip tip as you turn it back right side up.
I have had nothing but success doing it this way. Try it and let me know how it goes.
I shall have a smack at it next time I build one
Did you see the photos of the final one? I don't think its ugly, but it looks similar to the Bellus, which I also don't think is ugly
VaporDNA and GB have it in stock.
Top fill is definitely plastic bottle/unicorn bottle. I told them when I saw the prototype they would get some complaints about that. I filled it in about 4seconds using a plastc squeeze bottle. But, I have a ton of RTAs that don't fill well with an eye dropper or it takes too long for top filling, so I tend to put all juice into plastic bottles. However, if you're an eye dropper guy or gal, you won't like the top filling.
, No, just the prototype. Thanks, I'll look it up.Did you see the photos of the final one? I don't think its ugly, but it looks similar to the Bellus, which I also don't think is ugly
VaporDNA and GB have it in stock.
Top fill is definitely plastic bottle/unicorn bottle. I told them when I saw the prototype they would get some complaints about that. I filled it in about 4seconds using a plastc squeeze bottle. But, I have a ton of RTAs that don't fill well with an eye dropper or it takes too long for top filling, so I tend to put all juice into plastic bottles. However, if you're an eye dropper guy or gal, you won't like the top filling.
I continued posting pics in the thread as they sent them to me. There's a video, too.
I got mine yesterday so I'll post a pic of it also.
Beauty is in the eye of the beholder though . A lot of peeps think the Aromamizer is ugly, but the only thing I don't like is the drip tip neck.
I think the Flash e Vapor is hideous, and it took me months to buy one because of that. It looks much better with the glass tank kit though.
I also think the Erlk is ugly, but its a good vape for tootle puffing.
. A lot of peeps think the Aromamizer is ugly, but the only thing I don't like is the drip tip neck.I think the Flash e Vapor is hideous, and it took me months to buy one because of that. It looks much better with the glass tank kit though.
I also think the Erlk is ugly, but its a good vape for tootle puffing.
Ugly is in the eye of the beholder. It did clean up some in the finsl trim. I am concerned about air, though. I'm eagerly awaiting your reviews when you get them built and vaped in.
- Status
