you can get it on eBay a LOT cheaper than from me that's for sure...
Introducing the Griffin Rebuildable Atomizer Tank
- Thread starter gormly
- Start date
- th_trl_thread_readers 0
-
- Tags
- ecigexpress provari vamo vapor pro
- Status
you can get it on eBay a LOT cheaper than from me that's for sure...
Glass tank update. Bad newsThe OD of the top and bottom plates is 15.07mm with the O-ring it's 15.15mm. The only supplier that could do such a specific ID would have to retool his extruder. $$$$$$$$$$$$...$$$$$$$$$. and $$$$$$.
Sorry It's gonna have to be plastic.
I see above that the Ideal 12ml fits
awww... worth the shot right?
Countsmackula, I got it from ebay. 5.95 plus 1.95 for shipping. I am not sure i can post the link here. I will pm you the link.
Sorry Eric. I forgot about vendor thread etiquette.
that's quite all right, I only offer the wire and wick as a convenience, anyone serious should buy it elsewhere to save money.
In this particular instance you are free to post whatever you like for wick and coil.
I made sure not to 'fill' the hole up with wick - left a little space around the edges. Wicks like a monster! And, I can leave the fill screw in so no worries about juice sloshing out & around.
p.s. I'm not chain vaping, which would increase the wicking demand, so YMMV!
p.s. I'm not chain vaping, which would increase the wicking demand, so YMMV!
I tried it both on and off, May be ss wick is too tight? I am using ss 325 with 30/70 vg/pg.
I drilled out the wick hole to 7/64" Made a world of difference.
edit: After fiddling with this thing, It works like a champ. notes of caution: The threading is very loose on the center tube and the tiny ground screw. Don't tighten it down more than necessary to just hold the ground wire or it will strip. I found with the syringe tube it tightens up the main body very nicely and I have not had the shorting problems I was having with the metal tube in place. The top and bottom plates would move independent of each other and that would pull on the resistance wire via. the center post making the wick lean and short out when I screwed the device on my power supply (mod).
edit: After fiddling with this thing, It works like a champ. notes of caution: The threading is very loose on the center tube and the tiny ground screw. Don't tighten it down more than necessary to just hold the ground wire or it will strip. I found with the syringe tube it tightens up the main body very nicely and I have not had the shorting problems I was having with the metal tube in place. The top and bottom plates would move independent of each other and that would pull on the resistance wire via. the center post making the wick lean and short out when I screwed the device on my power supply (mod).
Last edited:
The 325 may be your issue. I've been reading that 400 mesh may be coarsest mesh you want. Supposedly 500 mesh is the current wicking top dog. http://www.e-cigarette-forum.com/forum/modding-forum/330407-500-ss-mesh.html
I am ordering the Clear Griffin tank tubes Now
Sweet. How long before they hit the site. Should have my griffin tomorrow.
I am ordering the Clear Griffin tank tubes Now
woohoo than I will mess with it again.
Yay clear griffin tanks!!!!
I just ordered some 500 mesh to see if it is really better
Be interested to hear about this. Ive only used 316 mesh and have 400 on the way. Riptrippers seems big on using 28AWG kanthal on their atty. wonder how it would fare on the griffin.
OK just ordered the tubes, the Griffin with the clear tube, some spare metal tubes, some orings, some top caps (so you don't have to buy a new one for the bigger hole)
- Status
Similar threads
- Locked
