Ithaka official
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
-
- Tags
- provari
- Status
Got my Ithaka today! My oh my...what a beautiful piece! I had a bit of trouble at first but this was due to loose internal parts. I dove right into the X style dual coils at 1.8 ohms (two 3.6 ohm wraps with 34 gauge wire)...amazing! Once the new wick taste is gone I will be one happy camper. And finally, a big THANK YOU to Imeo! Bravo!
Wow, switched over to dual "X" coils on 3mm using 1.5Ω ready wires. I know it shouldn't matter if they're touching but I built the base and then did nudge the coils to eliminate any touching wires (some coils didn't glow where contact was being made). I also closed the base feeder on this build and am just using the mouth piece juice feeder (open much more than I would've with Pennie or Ody). All I can say is WOW! What an absolutely stellar vape...
If anyone else has difficulty adjusting juice flow with the Drip Tip mouth piece, I've learned to loosen the smaller top cap. When the little cap is tight there isn't enough mouth piece sticking out for me to grab and the drip tip just spun in place.
If anyone else has difficulty adjusting juice flow with the Drip Tip mouth piece, I've learned to loosen the smaller top cap. When the little cap is tight there isn't enough mouth piece sticking out for me to grab and the drip tip just spun in place.
After 3 tanks of Shocker liquid from G2 Vapors (raspberry + absinthe/anise/licorice) my Ithaka tank is cracked.
I tried to make the picture this morning with Blackberry, it's not the best device for macro shots, but you can see this.
Results with Pluid will interest me.
Imeo, where I can buy spare plastic window in Europe, please? Will Vassilis help me?
edit: link to high res pic
http://cubeupload.com/im/Xcwj7K.jpg
I tried to make the picture this morning with Blackberry, it's not the best device for macro shots, but you can see this.
Results with Pluid will interest me.
Imeo, where I can buy spare plastic window in Europe, please? Will Vassilis help me?
edit: link to high res pic
http://cubeupload.com/im/Xcwj7K.jpg
Last edited:
Believe me Imeo, it's possible. When you screw Ithaka on the mod, brass pin or screwing-in as well. Logically you can expect that once its touching connection it's fixed, but thread is so loose that brass pin is screwing in as well. But I found solution how to avoid this with the teflon tape
Hi mate,
I believe that is the correct function of the brass centre pin and is actually designed to move whilst screwing onto your mod to eliminate any gap between the top of your device and the Ithaka
1. Unscrew the brass centre pin
2. Screw Ithaka onto your device
3. Brass centre pin will contact the centre pin on your device, but there will likely be a slight gap between the top of the device and Ithaka
4. Carry on screwing until Ithaka sits completely flush with no gap
During number 4, the brass centre pin will always remain in contact with the centre pin of your device but will screw in as you screw on the Ithaka.....this closes the gap between the top of your device and Ithaka whilst still keeping the brass centre pin of the Ithaka in contact with the centre pin of your device
It only loses contact if you screw and unscrew
Imeo, I found the right videos thanks to Ariel_MX, and I've gotta say... Holy $#!& man. What are they feeding u over there in Greece?
Getting amazing flavor. Smooth, perfect draw.. Two thumbs WAY up on this one. I just looked at my Pene like she was a red-headed step child..
You can retire now. I don't think it gets much better than this..
Getting amazing flavor. Smooth, perfect draw.. Two thumbs WAY up on this one. I just looked at my Pene like she was a red-headed step child..
You can retire now. I don't think it gets much better than this..
i agree with almost everything, but please...no retiring before the new ggts's and achilles is made
Imeo, I found the right videos thanks to Ariel_MX, and I've gotta say... Holy $#!& man. What are they feeding u over there in Greece?
Getting amazing flavor. Smooth, perfect draw.. Two thumbs WAY up on this one. I just looked at my Pene like she was a red-headed step child..
You can retire now. I don't think it gets much better than this..
I am really glad that you all enjoy your Ithakas guys and girls. It was not an easy project but it came out the best way it could come. Happy vapinggg!
Just got mine today, and... well, I'm really impressed. It's vaping incredibly well, looks great, no leaks. I love that I get air control on my other mods, even though I only tried it for a minute before it went back on my favorite GGTS.
With dual coils, none of my other attys put out anything close to the clouds I'm getting from my Ithaka. I love it!
With dual coils, none of my other attys put out anything close to the clouds I'm getting from my Ithaka. I love it!
I think you missed my point, lol.....you don't need the Teflon tape
But as long as you have it working like you want then its all good
Hi mate,
I believe that is the correct function of the brass centre pin and is actually designed to move whilst screwing onto your mod to eliminate any gap between the top of your device and the Ithaka
1. Unscrew the brass centre pin
2. Screw Ithaka onto your device
3. Brass centre pin will contact the centre pin on your device, but there will likely be a slight gap between the top of the device and Ithaka
4. Carry on screwing until Ithaka sits completely flush with no gap
During number 4, the brass centre pin will always remain in contact with the centre pin of your device but will screw in as you screw on the Ithaka.....this closes the gap between the top of your device and Ithaka whilst still keeping the brass centre pin of the Ithaka in contact with the centre pin of your device
It only loses contact if you screw and unscrew
I concur with this interpretation, I was surprised a bit until I realized what was happening. Then the first thought was "holy s* this is great!"
- Status
Similar threads
