seriously awesome work. comes with that DT too? completely stainless from head to to toe. me likey
Juggernaut Roll Call!!
- Thread starter Crack3dOne
- Start date
- th_trl_thread_readers 0
- Status
Love those pictures!!! Wow. I think I'm going to love this thing as much as my orion!!!!
the vape, hmmm, I was too lazy last night so i haven's set it up yet.
The bottom switch I believe is sturdy but I haven't fired it up yet so I can't be too sure. but compared to other hybrids I have with switches on the bottom, this one looks better.
You're gonna like what you see ...
Last edited:
Jugg coming tomorrow! dang they shipped that fast. hey .... did it come with any mesh or anything? i'm almost out and don't want to waste my last bit if not
it did come with mesh that has oil, I can tell because it looks like it came thru a rainbow 
, a few feet of wire and 3 o rings if I'm not mistaken
, a few feet of wire and 3 o rings if I'm not mistaken
here is my ugly mug on the Jug
I do apologize for the video quality, I only used my tablet to shoot it. and the tip I used is not the one that came with it.
Couple of things I noticed.
- you have to mount your wick/s as tight as you can on the hole/s
- if you're using single wick you better plug the other hole
I don't know if it's my fault but I see a lot of the juice left on top and on the side of the cap. I've only used it for 30mins and there's about 1ml left of juice on the tank. Maybe it's just me, my knowledge on wicks and coils are limited to my Zens
Last edited:
nice!!!!!! appears to be pluming nicely. How's the throw on the switch? I saw a vid saying it was very short like 1mm which sounds nice!
man i am loving the way the top cap snaps on. what did mac say? snap, crackle pop!
man i am loving the way the top cap snaps on. what did mac say? snap, crackle pop!
hmmm yeah that sounds discouraging about the juice on the side and top. You think it could be overwicking and leaking out when you tilt?
it is nice. I never realized it was vaping that good until I saw my own video. Im a cigar/pipe guy so I have no way of knowing
The switch was pretty easy to get used to.
it's on 1.7ohms 500SS, 32Ga. I used petar k method. so maybe that's the reason I have juice all over the top portion. I never over tilt but I think it's over wicking or my wick's too slim. Wick hole's around 3/32" but my wick was just 5/64".
but you really need to plug that other hole just like on the cobra, unless you want juice all over the dang top
How are you planning to set up yours?
The switch was pretty easy to get used to.
it's on 1.7ohms 500SS, 32Ga. I used petar k method. so maybe that's the reason I have juice all over the top portion. I never over tilt
but I think it's over wicking or my wick's too slim. Wick hole's around 3/32" but my wick was just 5/64".but you really need to plug that other hole just like on the cobra, unless you want juice all over the dang top
How are you planning to set up yours?
Last edited:
good tips man thanks! I will make a fatter wick than normal and make sure to plug the other hole. I noticed in the dux video he was using what appeared to me to be an extremely fat wick. much fatter than what i normally use.
Don't think I have enough mesh to try a u wick
32 gauge twisted method has been working great for me lately. i'll let you know as soon as I get it. I have wick oxidized ready to go
Don't think I have enough mesh to try a u wick
32 gauge twisted method has been working great for me lately. i'll let you know as soon as I get it. I have wick oxidized ready to go
you know I just ran the wick on the blue flame of my lighter then I pulsed it on the jag for like 15 times.
well I did dual coils this time with super tight wicks. width at around 35mm unrolled but it still doing it. I did notice that the tank is a tad short that you can poke the oring. I move the tank up a lil bit and inserted an oring from an AGA. hope this fixes my issue.
I'm not sure if it's just my OCD or if I'm doing anything wrong lol
I'm not sure if it's just my OCD or if I'm doing anything wrong lol
Last edited:
stalking mailman.....
.... lemme know how the oring change is workin for ya
Sweet dual wick setup though!
.... lemme know how the oring change is workin for ya
Sweet dual wick setup though!
I think I'm going to make a uwick dual coil when my piece arrives. I"m thinking the peter k method and slipping the wick in there. We will see
So, are both of the air holes suppose to be drilled all the way through. One of mine is, and the other is only half drilled. From the outside it appears that it is drilled through, but the second hole is not drill through on the backside. Luckily I have a 1mm TiN drill bit to finish the job. I was wondering why the pull was so stiff, lol.
Sent from my Transformer TF101 running on SS mesh & Kanthal.
Sent from my Transformer TF101 running on SS mesh & Kanthal.
- Status
Similar threads
- Locked
- Locked
