Juggernaut Roll Call!!
- Thread starter Crack3dOne
- Start date
- th_trl_thread_readers 0
- Status
I fixed the wobble by placing a #15 red oring between the battery and cap.
Sent from my SGH-T989 using Tapatalk 2
Sent from my SGH-T989 using Tapatalk 2
can i see some pictures pleaseSmall hands?
I like to knuckle, which gives the normal press. If I use the tip of my middle finger I get the hard press. I like to switch it up. No wonder I'm getting different vapes each time. Sometimes I like to be a posh vapist, using the pinky. Ok, that's enough of that.
On another note. I noticed that the airhole is lines up more so with the bottom of the wick. So I made a new coil; kinda of backwards from the orion, whose airhole lines up more so on the top of the wick. I have a leader coming down from the top and my coil wrapped down low. So far I'm getting bigger vape clouds, same taste. Still testing.
Sent from my Transformer TF101 running on SS mesh & Kanthal.
thanks
Sent from my Samsung S III running on SS mesh and kanthal.
That's how i first set i up. Petar k, single wick, lead on top of the coil lol. But my wick is not as tight. Today, I put a 90mm 635ss mesh 3/4 28ga coil and the dang thing still is condensing really bad. I think it's either an issue with the oring or i am sucking on it like a kid on a gogurt
And thanks for posting the image
i like it a lot. the tight draw is a great change from my other stuff. flavor and TH are top notch. vapor much weaker because of tiny air hole but i dont mind since that makes the draw tight and increases TH.
how bout u b?
I thing the battery tube is to small is diameter. Plus, if it wasn't, you would have to shove the sick all the way up in the tube. The tube is monolithic with the tank/atty section.
On another note, I'm going to have to renege on what I said about dual wicks earlier. I just install this set up, two 4/3 wraps of 30awg kanthal a1 coming in at 0.5ohm. Made the coils from one single strand the peter k method, starting at one screw, going up the drill bit rod and around the back of the top screw and coming back down the second drill bit rod, with two 60mm 500 mesh wicks. Now if you excuse me, I need to go find and pick up the back of my throat off the floor and jump start my lungs.
27 watts
On another note, I'm going to have to renege on what I said about dual wicks earlier. I just install this set up, two 4/3 wraps of 30awg kanthal a1 coming in at 0.5ohm. Made the coils from one single strand the peter k method, starting at one screw, going up the drill bit rod and around the back of the top screw and coming back down the second drill bit rod, with two 60mm 500 mesh wicks. Now if you excuse me, I need to go find and pick up the back of my throat off the floor and jump start my lungs.
27 watts
Last edited:
that's talent right there.
One single strand? Nice bro. I just did a wick in a wick. That's going pretty nice. Did y'all see Macs review of the jugg? Pretty long and in depth video. He also suggested (if not using dual wicks/u wick) to put a small piece of mesh in the other wick hole to help with condensation. I haven't had any issues with that really. This thing is a beast.
Next step. Dual wicks or maybe a u wick.
One single strand? Nice bro. I just did a wick in a wick. That's going pretty nice. Did y'all see Macs review of the jugg? Pretty long and in depth video. He also suggested (if not using dual wicks/u wick) to put a small piece of mesh in the other wick hole to help with condensation. I haven't had any issues with that really. This thing is a beast. Next step. Dual wicks or maybe a u wick.
The red.oring from the aga helped minimize it as well.
Hehehe crack, i lost my throat as well with the dualie but i since have learned to live with. I setup a single and went back to dual after 5 sucks on the jug. Im sticking with that setup on the jug.
Hehehe crack, i lost my throat as well with the dualie but i since have learned to live with. I setup a single and went back to dual after 5 sucks on the jug. Im sticking with that setup on the jug.
Last edited:
I love it I'm using a single wick for now. I'll try a dual wick later on today.
Sent from my SGH-T989 using Tapatalk 2
Sent from my SGH-T989 using Tapatalk 2
What's the difference between the 2 orings?
I'm thinking about opening the second air hole to get more vapor.
Sent from my SGH-T989 using Tapatalk 2
I'm thinking about opening the second air hole to get more vapor.
Sent from my SGH-T989 using Tapatalk 2
I'm talking about this ...
I did that because I notice that this has way too much condensation compared to my other mods. those two additional o-rings helped minimized it, or so I thought
When you do decide to open that hole, give some feedback please.
Last edited:
How you liking your jugg so far?- Status
Similar threads
- Locked
- Locked
