- Status
Yeah, they are 
. I got one; but am waiting on some of those 510 connections from FT before doing anything with it
Sent from my iPod touch using Tapatalk
. I got one; but am waiting on some of those 510 connections from FT before doing anything with it Sent from my iPod touch using Tapatalk
Yeah, they are
Sent from my iPod touch using Tapatalk
Thinking of paralleling two for 6 amps, like we did with the DNA12.
The pot's to the right of the LCD display, so it's not the onboard one. Mine was different to the one on your board though.
I buy these by the dozen. Easy to mount with the nut and also easy to solder the neg wire to the nut.
https://www.fasttech.com/products/1563302
Since most of my attys are Evods I purchase these:
$1.30 510 to eGo Adapter Convertor for E-Cigarette at FastTech - Worldwide Free Shipping
They don't come with the "nut" so I purchase the 510 to 510 to get the nut.
Was poking around on eBay and saw these:
2 Cells 6A 15A Peak Li ion Lithium 18650 14450 Battery in Out Protection PCB | eBay
Was wondering if I could use this to do in mod charging of 2 18650 batteries in series. Don't really see any info on the input voltage for this though. Or possibly do the wiring for this in mod and have a 6 pin or so Molex out to an in on a separate "charging box" with all the circuitry. Been following the thread for a while now and haven't seen much along the line of in mod charging.
2 Cells 6A 15A Peak Li ion Lithium 18650 14450 Battery in Out Protection PCB | eBay
Was wondering if I could use this to do in mod charging of 2 18650 batteries in series. Don't really see any info on the input voltage for this though. Or possibly do the wiring for this in mod and have a 6 pin or so Molex out to an in on a separate "charging box" with all the circuitry. Been following the thread for a while now and haven't seen much along the line of in mod charging.
When I want to charge batteries in series on board. I install the shrouded end of one of these cables on the box mod and use an extension to charge from one of my RC balancing charger, I do this for my mods with flat lipos. With round cells it is just easier to change batteries.
I know this has probably been asked and answered, but I would rather not look through 1000+ post to find it. Has anyone come up with a "Pot" value to replace the trimmer that is responsive in the 3-6 volt range? The trimmer on mine is kind of touchy when trying to adjust .1 volt.
Thanks for the reply. I think I have some odd "Pots" in my shop. I'll do some experimenting and see what results I get.
Here is a smaller meter for our mods. Now to get Bapgood to draw us a frame for this one for shapeways.
DC 2 5V to 30V Red Blue Green Digital Voltmeter Meter Power Monitor Panel Meter | eBay
DC 2 5V to 30V Red Blue Green Digital Voltmeter Meter Power Monitor Panel Meter | eBay
Here is a smaller meter for our mods. Now to get Bapgood to draw us a frame for this one for shapeways.
DC 2 5V to 30V Red Blue Green Digital Voltmeter Meter Power Monitor Panel Meter | eBay
I used the same meter for my last two homemade mods except color is red. They work well. I just ordered two more. I get them here:
K1BO Mini DC 2 5 30V Red LED Panel Voltage Meter 3 Digital Display Voltmeter | eBay
Not the same. Yours is 24mm x 15mm. I have used dozens of these and there is a frame for these at shapeways. Looking for smaller.
This says 24mm x 10.5mm
Mini 0 28" DC 2 5 30V Blue Green Red Digital Voltage Panel Meter Voltmeter | eBay
Last edited:
- Status
Similar threads
