Killer 705 atty

Status
Not open for further replies.

Tennovan

Super Member
ECF Veteran
Verified Member
Jul 22, 2011
422
240
Texas
I ordered the 1st and received the shipping notice on the 5th - received today. USPS ~ they wonder why people don't like using them. No scanning progress at all until it arrived local.

Ok so essentially 2 weeks from order to delivery. Not bad... which site did you order from again? I'm too lazy to go back and check haha.

And yeah one thing I hate about the USPS is that they give you a "tracking" number, but the service they technically claim to provide is simply "delivery confirmation". That means the tracking number is really only intended to inform us whether/when the item was delivered or not... which is kind of dumb because the recipient will be able to tell you that 99% of the time without the tracking number. Any scans between initial processing and delivery can be shown but aren't required to be. I could be mistaken but I think the only service they provide with point-to-point tracking is Express Mail.
 

SheerLuckHolmes

Ultra Member
ECF Veteran
Verified Member
Jul 28, 2009
1,354
562
74
Tempe, Az
Tried using it as a dripper at work. Hardly any vapor. When I got home I set it up in a tank. Very nice for about two minutes, then vapor dropped off. I started watching the ohms... 1.8 up to 4.2 & everywhere in between. This sucks! I just do not have time to rebuild the wick & coils until Sunday. Gotta say I am very disappointed. Wait two weeks... Now I gotta wait two more days to play around with it. For the money I should not have to screw around with this.
 

Dnerve

Senior Member
ECF Veteran
Verified Member
Jan 11, 2013
142
94
Ireland
Tried using it as a dripper at work. Hardly any vapor. When I got home I set it up in a tank. Very nice for about two minutes, then vapor dropped off. I started watching the ohms... 1.8 up to 4.2 & everywhere in between. This sucks! I just do not have time to rebuild the wick & coils until Sunday. Gotta say I am very disappointed. Wait two weeks... Now I gotta wait two more days to play around with it. For the money I should not have to screw around with this.

Sounds like a bad/shorted coil...But trust me you got to persevere in your efforts.

This nasty little device is a bit sensitive on the setup side of things but becomes very rewarding when you get the hang of it.
 

dspin

Vaping Master
ECF Veteran
Verified Member
Sep 2, 2010
7,513
8,328
USA
Yes. The section between the Killer and adapter, where the liquid feeder holes are, is whats opening. This is causing the killer to lift off the positive floating pin. The floating pin is a great idea but it needs to move w the Killer. Spring loaded. Anything.


K, are you sure you need the Killer extension piece with the Ody. One doesnt use extension with the UFS, but I have never fiddled with my expansion pack for Ody.
 

kwalka

Unregistered Supplier
ECF Veteran
Jan 23, 2012
3,581
4,536
Clearwater, Florida
walkers-finest.com
K, are you sure you need the Killer extension piece with the Ody. One doesnt use extension with the UFS, but I have never fiddled with my expansion pack for Ody.

I've stopped using it w Ody, because it keeps the feeder holes too high off the bottom of the tank. Even w/o the adapter. I made a tank out of syringes while I wait for the new one, and its the same thing. The Killer must be built with the adapter set so the juice is always open. It doesnt seem to flood. It just does not do what it is advertised to do. Come on Imeo... ;)

Im sure it works great with UFS, BTW.

EDIT:
The Killer 705 has nothing to do with GG or Imeo. That was an inside joke between friends.
 

SheerLuckHolmes

Ultra Member
ECF Veteran
Verified Member
Jul 28, 2009
1,354
562
74
Tempe, Az
Snuck in some time this morning. It all boils down to the negative wire coming out of the little slot to be trapped in the threading as you screw on the top cap. If that doesn't get caught just right, the oms are all over the place and very poor vapor. When it is seated well, the killer is a killer.
 

Dnerve

Senior Member
ECF Veteran
Verified Member
Jan 11, 2013
142
94
Ireland
Snuck in some time this morning. It all boils down to the negative wire coming out of the little slot to be trapped in the threading as you screw on the top cap. If that doesn't get caught just right, the oms are all over the place and very poor vapor. When it is seated well, the killer is a killer.

Yeah, make sure to have a little lead go further under the last thread that will be covered by the top part.
 

gheebee

Senior Member
ECF Veteran
Jun 20, 2011
144
77
North America
Got my Killer 705 today and while I didn't expect it to come with wicks and wires, I was pretty annoyed that mine didn't have a ceramic in it. $75 and they couldn't include this? The least they could have done was put that on the page so you know to buy some or buy some CE2s. Between that, the imperfections in the rim where the drip tip goes, and the unimpressive threading on the atomizer portion, I'm already sorry that I bought this.
 
Last edited:

Fr3shMak3r

Full Member
Verified Member
Oct 20, 2012
64
72
United States
Got my Killer 705 today and while I didn't expect it to come with wicks and wires, I was pretty annoyed that mine didn't have a ceramic in it. $75 and they couldn't include this? The least they could have done was put that on the page so you know to buy some or buy some CE2s. Between that, the imperfections in the rim where the drip tip goes, and the unimpressive threading on the atomizer portion, I'm already sorry that I bought this.

That definitely isn't right. Mine came fully prebuilt with a coil and ceramic.

Also, mine has no imperfections build-wise. I would definitely contact the vendor about that situation and get a replacement.
 

tmcase

ECF Guru
ECF Veteran
Verified Member
Apr 20, 2011
20,862
54,652
Got my Killer 705 today and while I didn't expect it to come with wicks and wires, I was pretty annoyed that mine didn't have a ceramic in it. $75 and they couldn't include this? The least they could have done was put that on the page so you know to buy some or buy some CE2s. Between that, the imperfections in the rim where the drip tip goes, and the unimpressive threading on the atomizer portion, I'm already sorry that I bought this.

Oh no. Please don't tell me you have to order the ceramic cup separately. That's insane. :(
 
Status
Not open for further replies.

Users who are viewing this thread