Let's Talk Hardware

[DavidOH]

This is something I haven't seen. A place to get twisted wire.
Twisted Build

 

[Dusty_D]

GT joined Facebook and I've added him to the Army page .. that's all I'm saying!

Come say Hi!

For the newbies, here's the page: https://www.facebook.com/groups/hhvarmy/

 

[retic1959]

Overall, I am happy with the threading. Only issue I had was a small burr on the edge of one of the tank sections. Oh, and I quickly cracked a tank using coffee liquid. My fault totally.

Angelcigs. Well, they took a bit to finally ship out, and when they did, it was the wrong item. (They sent me a lite instead.) HOWEVER, upon notifying them, they quickly shipped out a 3.1, and never asked me to send the lite back. Very classy of them.

Thanks Hudson ! Yeah that is nice of them to let you keep the lite , that answers my question .

 

[Chakris]

Yeah Chak. GT started with a ProSmoke too. What a total piece of krap that was. An automatic battery. What a failed concept. They still send me emails.

Unsubscribe...

I started with a KGO and cartos. It worked well enough to keep me off of the stinkies. I pretty quickly went to clearos instead of cartos. Then I got a V-Tube (lavatube clone), a Reo and a Silver Bullet, and graduated to the Vivi Novas.

With the Provari and the HCigar Kayfun 3.1's, I feel like I'm in vape nirvana.

I believe I went the carto route as well after the ProCrap. Carto tank on the Odyssey mech got me off the stinkies along with those ego tanks - what the heck do they call them again? Joyetech eGo-T - the ones where the tank is incorporated into the tip and pushes down onto the attomizer - had to look it up. After that in quick procession, ViVi Nova, Kanger T3, eVod, Protank with a few RBAs thrown in for good measure, like 2 AGA-T2s, 2 Richaman Genesis clones, and 3 SplitFires.

Ekowool sucked in the Kayfuns. Cotton beats all in the KFL's..


Sent from my iPhone using Tapatalk 2

I keep switching from cotton to silica, but lean towards cotton. Running sort of low on 1.5mm silica, but have 20 some odd feet of 3mm hollow thread. Maybe I'll make a Jacob's ladder with it and use it on the Bar-B

Built my first twisted kanthal coil. 32g, 3 wire, cant remember how many turns around my 2mm or so screwdriver. MVP shows it at 1.7. Seems VERY slow to heat

You can either go Dusty's route or drop a strand on your next build.

Sorry. I am still learning

No need to apologise, we've all been through the same thing. (and not all that long ago)

And I'm learning with you. I've done double wraps. Need a test dummy subject for triple wrap 32.. Go!!


Sent from my IdeaTab S6000-F using Tapatalk

Fixed that for ya, buddy.

Maybe I will just make another one for my dripper. The first is in the kayfun 3.1

Got yer thinking cap on... If it ain't broke, don't fix it.

 

[Chakris]

Unless, of course you've got nothing better to do...

 

[Bunnykiller]

This is something I haven't seen. A place to get twisted wire.
Twisted Build

the tiger wire is 7.50 for 3 feet?!?! wonder how many ohms per inch its rated at??

 

[DavidOH]

the tiger wire is 7.50 for 3 feet?!?! wonder how many ohms per inch its rated at??

Don't know but I made one last night. Put a coil in the RBA. Came in at .5 with about a 3 wrap. The flavor is good but I think it's to hot for the RBA. I'll be putting a .8 ribbon coil back in it later. I have enough for another coil. I may put it in the KFL but I'm liking the ribbon so much I'm not sure I want to change at this point.

 

[Bunnykiller]

Don't know but I made one last night. Put a coil in the RBA. Came in at .5 with about a 3 wrap. The flavor is good but I think it's to hot for the RBA. I'll be putting a .8 ribbon coil back in it later. I have enough for another coil. I may put it in the KFL but I'm liking the ribbon so much I'm not sure I want to change at this point.

how does the ribbon look when dry burned?? does it heat up evenly across the width of it?

 

[DavidOH]

how does the ribbon look when dry burned?? does it heat up evenly across the width of it?

The RBA is an A7 so it's only has like 2/3 wraps and I use .8 ribbon. The KFL I use .6 ribbon and do a 5/6 wrap at 3/32. Just putting new wick in the coil that has been a week. It still looks good and is heating from the middle out.

 

[MwSlim]

Anyone else been using a Stillare? I love this dripper

Tapatalked from my LG-G2

 

[Dusty_D]

Anyone else been using a Stillare? I love this dripper

Tapatalked from my LG-G2

I've been eyeing it, but haven't pulled the trigger on it yet. Could be the fact that I have a half dozen drippers sitting around not being used that causes me to hesitate.


Sent from my IdeaTab S6000-F using Tapatalk

 

[MwSlim]

I've been eyeing it, but haven't pulled the trigger on it yet. Could be the fact that I have a half dozen drippers sitting around not being used that causes me to hesitate.


Sent from my IdeaTab S6000-F using Tapatalk

Same thing here, Dusty. I have a ton of drippers that I never use but this thing I cant put down. It is simple to set up and it performs great. I love the airflow adjustment too

Tapatalked from my LG-G2

 

[Bronze]

No Slim. Elaborate.

 

[MwSlim]

No Slim. Elaborate.

I really dont know what it is that makes it better lol it just is

Tapatalked from my LG-G2

 

[Bronze]

That helps.

How about a link?

 

[MrPicC]

I know. Its new.. Give it a few weeks

Sent from my SAMSUNG-SGH-I747 using Tapatalk

 

[MwSlim]

That helps.

How about a link?

I picked it up at my local B&M lol im no help here at all

Tapatalked from my LG-G2

 

[Bronze]

I picked it up at my local B&M lol im no help here at all

Tapatalked from my LG-G2

In other words, you're like a beautiful girl...a tease!!!

 

[Bunnykiller]

I picked it up at my local B&M lol im no help here at all

Tapatalked from my LG-G2

ahhhh you are in the middle of a vapegasm??? cant see straight or think clear and lucid thoughts??

 

[DavidOH]

That helps.

How about a link?

Stillare Atomizer Clone RDA