Lurking?? How to find a home within all the forums and threads?

Status
Not open for further replies.

Steve803

Senior Member
ECF Veteran
Aug 21, 2013
211
1,516
Deland, Fl
vapinggenius.com
Oh ... well, yes in that case. Same problem here:(
Here I was all content & happy with my little ole' eGo's & then LB & Chim got me all wound up about these "other" things:facepalm:
And juice? Let's not even go there! :ohmy: Why does it have to start out good then go bad? :grr:

Dale. What do you mean go bad. I haven't had any juice go bad.


Sent from my mobile device using Tapatalk
 

Steve803

Senior Member
ECF Veteran
Aug 21, 2013
211
1,516
Deland, Fl
vapinggenius.com
OK, nobody pass out from shock, but I'm back! Other than supporting Robin & Tvans effort, I've been on an internet break. Took me hours to catch up, so remind me not to do that again :lol: There's too much to remember that I can't even begin to comment individually. Welcome to all the new members. It looks like overall, things are going well for everyone.

Hi charm. I've seen your name referenced many times. The Lurkers are an awesome group. :)


Sent from my mobile device using Tapatalk
 

charmschool

Super Member
ECF Veteran
Verified Member
Feb 24, 2013
431
4,974
North Georgia
Ah, you need to stop looking at all the new toys everyone shows here! ;)

I've settled on what I'm using pretty much from the beginning. Nova and PV. The only thing that changed was going from an eGo to a Provari. But that's just me. I hate fiddling and not much of an experimenter.

Are you just not satisfied with what you're using? Or having problems?
Why do you think I took a break, lol! Of course I look at everything, and that makes me think I NEED everything....no problems, just trying to figure out how to balance my new hobby/addiction with my old life. Vaping has been my ONLY focus for 10 months, to the detriment of all my other responsibilities (and relationships). It's been necessary to reset my smoking "triggers", but I have to figure out how to fit some things back in again, or my home & yard will be condemned, and my family & friends will forget who I am. Well, I'm exaggerating a bit, but I've let a lot of things slide making the transition.
 

Steve803

Senior Member
ECF Veteran
Aug 21, 2013
211
1,516
Deland, Fl
vapinggenius.com
I'm looking forward to my first Florida winter :evil:
I'm now seeing people talk about colder nights and fall temps back north. Hahaha. Still hot here! I'm loving it!

You'll like the winters in Ft Pierce. :) If i remember correctly from when i grew up in ft lauderdale we rarely got below 60 with an occasional frost. Of coarse after a few year down here anything below 70 is chilly. Brr


Sent from my mobile device using Tapatalk
 

Steve803

Senior Member
ECF Veteran
Aug 21, 2013
211
1,516
Deland, Fl
vapinggenius.com
Why do you think I took a break, lol! Of course I look at everything, and that makes me think I NEED everything....no problems, just trying to figure out how to balance my new hobby/addiction with my old life. Vaping has been my ONLY focus for 10 months, to the detriment of all my other responsibilities (and relationships). It's been necessary to reset my smoking "triggers", but I have to figure out how to fit some things back in again, or my home & yard will be condemned, and my family & friends will forget who I am. Well, I'm exaggerating a bit, but I've let a lot of things slide making the transition.

Oh yeah....the forum can be addicting just as much as taking that smoke break every 20 minutes. :grr:


Sent from my mobile device using Tapatalk
 

charmschool

Super Member
ECF Veteran
Verified Member
Feb 24, 2013
431
4,974
North Georgia
Oh ... well, yes in that case. Same problem here:(
Here I was all content & happy with my little ole' eGo's & then LB & Chim got me all wound up about these "other" things:facepalm:
And Juice? Let's not even go there! :ohmy: Why does it have to start out good then go bad? :grr:
And how many drip trips do we really need? :lol: :facepalm:
 

daleron

ECF Guru
ECF Veteran
Verified Member
  • Apr 16, 2013
    21,334
    380,974
    Arkansas, USA
    And how many drip trips do we really need? :lol: :facepalm:

    Shhhhhhhhh!:laugh:


    Isn't this the cutest thing? :)
    1014004_682005568482658_263169332_n.jpg
     

    Steve803

    Senior Member
    ECF Veteran
    Aug 21, 2013
    211
    1,516
    Deland, Fl
    vapinggenius.com
    Not that kind of "go bad" Steve; just that some of the things you like in the beginning you stop liking :)

    I get you. So true. I bought a bunch of the same juices when i first started and ended up give most of them away bc I lost my taste for tobacco flavors. Thats why i like to do DIY now. I'll make 5 or 6 - 5ml bottles of different flavors and mix them up over a couple of weeks til they're all gone and make some other flavors


    Sent from my mobile device using Tapatalk
     

    BDUAres

    Senior Member
    ECF Veteran
    Verified Member
    Nov 27, 2012
    147
    282
    Texas, USA & London, UK
    Thats a nice unit. Manly. Where did you get it?

    It's an $18 V3 Sentinal clone from Fasttech, in all brass, with the firing button lock ring removed (they seem to sometimes be defective and not lock correctly, so I was uncomfortable with that) and replaced the lock ring with a 3/8 brass compression cap from Home Depot. It not only perfectly matches, but is much sturdier than the original locking ring and allows the mod to stand up on a table much better.

    Since I like my original Protanks and they have a problem drawing air on some mechs, this one included, due to fitting flush against the top, I added an Ego to 510 adapter with some air holes drilled in it, and added a brass Ego beauty cone also with air holes drilled into it. I also expanded the air holes in the Protank bases slightly. I put a rubber washer between the cone and the top cap of the mech purely for aesthetics as there was a slight gap, and it came out looking like a gold light saber. My next move will be to sand down the pair of Protanks I use as they are brass under the chrome.

    Manly it is. It is pretty much indestructible, simple, very heavy and looks pretty good even when scuffed up and used rough.

    20130921_134718_zps2160a0e7.jpg

    20130921_134702_zps4b2329aa.jpg
     

    charmschool

    Super Member
    ECF Veteran
    Verified Member
    Feb 24, 2013
    431
    4,974
    North Georgia
    Oh yeah....the forum can be addicting just as much as taking that smoke break every 20 minutes. :grr:


    Sent from my mobile device using Tapatalk
    Forum? Pfft! You didn't mention the FB groups (12), my local vape club, not to mention all the shopping & crafting that must be done to support my "show us your pretty" addiction......
     

    Steve803

    Senior Member
    ECF Veteran
    Aug 21, 2013
    211
    1,516
    Deland, Fl
    vapinggenius.com
    It's an $18 V3 Sentinal clone from Fasttech, in all brass, with the firing button lock ring removed (they seem to sometimes be defective and not lock correctly, so I was uncomfortable with that) and replaced the lock ring with a 3/8 brass compression cap from Home Depot. It not only perfectly matches, but is much sturdier than the original locking ring and allows the mod to stand up on a table much better.

    Since I like my original Protanks and they have a problem drawing air on some mechs, this one included, due to fitting flush against the top, I added an Ego to 510 adapter with some air holes drilled in it, and added a brass Ego beauty cone also with air holes drilled into it. I also expanded the air holes in the Protank bases slightly. I put a rubber washer between the cone and the top cap of the mech purely for aesthetics as there was a slight gap, and it came out looking like a gold light saber. My next move will be to sand down the pair of Protanks I use as they are brass under the chrome.

    Manly it is. It is pretty much indestructible, simple, very heavy and looks pretty good even when scuffed up and used rough.

    20130921_134718_zps2160a0e7.jpg

    20130921_134702_zps4b2329aa.jpg

    Very nice!!! Good info too. I will archive this for future reference. I have all the tools to mod a unit like this. Way too cool. :)


    Sent from my mobile device using Tapatalk
     

    BDUAres

    Senior Member
    ECF Veteran
    Verified Member
    Nov 27, 2012
    147
    282
    Texas, USA & London, UK
    I have all the tools to mod a unit like this. Way too cool. :)

    The only tool needed was my drill with my smallest drill bit. I added new holes to the beauty cone and Ego/510 adapter which did not come with any, and merely enlarged the holes in the Protank base, all by hand on the edge of my computer desk. The adapter drilling was a lesson in what not to do, as I did not remove the inside firing pin first and ended up killing it with the drill, and I had to make another from various leftover ecig head parts I happened to have lying around in my kit. Oops

    For the $25 or so I have invested in it, this mech has been a very good buy
     

    Steve803

    Senior Member
    ECF Veteran
    Aug 21, 2013
    211
    1,516
    Deland, Fl
    vapinggenius.com
    Forum? Pfft! You didn't mention the FB groups (12), my local vape club, not to mention all the shopping & crafting that must be done to support my "show us your pretty" addiction......

    Omg....noooo i haven't gotten into all that. I have dropped a pretty penny on the new hobby but no where near what i spend on smokes a d lighters. Ugh. That would not be good. :(


    Sent from my mobile device using Tapatalk
     

    Steve803

    Senior Member
    ECF Veteran
    Aug 21, 2013
    211
    1,516
    Deland, Fl
    vapinggenius.com
    The only tool needed was my drill with my smallest drill bit. I added new holes to the beauty cone and Ego/510 adapter which did not come with any, and merely enlarged the holes in the Protank base, all by hand on the edge of my computer desk. The adapter drilling was a lesson in what not to do, as I did not remove the inside firing pin first and ended up killing it with the drill, and I had to make another from various leftover ecig head parts I happened to have lying around in my kit. Oops

    For the $25 or so I have invested in it, this mech has been a very good buy

    Thats easy enough. Guess i wont be need the drill-press after all.


    Sent from my mobile device using Tapatalk
     
    Status
    Not open for further replies.

    Users who are viewing this thread