Merlin by Augvape and Roxy
- Thread starter MMW
- Start date
- th_trl_thread_readers 0
-
- Tags
- augvape merlin single coil
- Status
I put all my Kayfuns away too. This IS the best RTA.Thought I would be set once got 1 more silver and a black one, but now I've seen how good the black one looks, might have to get another one.
@ricks these have made me put the kayfun mini v3's in the backup draw now
Also I never bothered with the stock drip tip, to wide for my vaping style, I have high power mods, but MTL vaping at a massive 16 watts
As you use it it becomes easier to turn
i have two one was very hard to turn in the beginning but now its perfect
I just posted this over at Bird Land, I'll post it here also.
I have here the "unofficial" o-ring sizes, I didn't check as to where they go, I just measured what was in the bag.
Three 5 x 1 mm
One 8 x 1 mm
One 12 x 1 mm
One 14 x 1 mm
Two 20 x 1.2 mm
Am I sure these are the correct sizes of the ones in the bag? Yep
Edit: The one between base and chamber is 15 x 1 not 14 x 1 mm, still may work just fine, not sure.(14 x 1 mm is what's in the bag)
Under the top cap (outer edge) and at the ends of the glass are the 20 x 1.2 mm, three are needed, two are included.
The 8 x 1 goes in the middle between the juice filling slots under the top cap.
The 5 x 1 mm goes on the end of chimney tube at chamber, might fit the drip tip also, didn't check.
As for the 12 x 1 mm, I haven't the slightest idea unless some how the base comes apart and it's for the AC ring.
I have here the "unofficial" o-ring sizes, I didn't check as to where they go, I just measured what was in the bag.
Three 5 x 1 mm
One 8 x 1 mm
One 12 x 1 mm
One 14 x 1 mm
Two 20 x 1.2 mm
Am I sure these are the correct sizes of the ones in the bag? Yep
Edit: The one between base and chamber is 15 x 1 not 14 x 1 mm, still may work just fine, not sure.(14 x 1 mm is what's in the bag)
Under the top cap (outer edge) and at the ends of the glass are the 20 x 1.2 mm, three are needed, two are included.
The 8 x 1 goes in the middle between the juice filling slots under the top cap.
The 5 x 1 mm goes on the end of chimney tube at chamber, might fit the drip tip also, didn't check.
As for the 12 x 1 mm, I haven't the slightest idea unless some how the base comes apart and it's for the AC ring.
I absolutely love the stock drip tip. I'm actually trying to find the same style but in different colors.
Sent from my iPhone using Tapatalk
It was mentioned on that other place that some of the loose AFC rings might have the wrong o-ring installed in them. It was suggested to send an email to STS (if that is where you bought it) about the issue.
Really too bad that clown showed up in the Merlin thread, the DB thrives on conflict.
Really too bad that clown showed up in the Merlin thread, the DB thrives on conflict.
Well I found out that there is such a thing as too much cotton. My 1st con is the fact it won't keep up chain vaping at 40 watts. This is my personal con because I'm sure that it's my technique and not the tank. So with that being said, the Bachelor is still the one I'm going to use first. I really thought this would be "The One". Oh well.
Sent from my LG V10 using Tapatalk
Sent from my LG V10 using Tapatalk
Thanks for the photo's bookmarked the post, for when my Merlin arrives. It is still on back order at FT until tomorrow, fingers crossed they actually ship.
I just Love these Merlins... Will have to try all different size wire and wicks and see how well they work in these. I have always found that 30g gave me the best flavor in my other tanks but I think I should try some thicker wires in these. I have some 28g SS that I recently got. I think I will try that first.
I will not be getting the KV5 now. Don't think it will be as good as these.
I will not be getting the KV5 now. Don't think it will be as good as these.
Last edited:
I'll be putting the notched coil in mine first, I liked that coil in the Theorem.
Easy wicking too with Sally's Rayon, you just pull the whole strand through since the coil ID is 5mm, then just trim up the tails.
Easy wicking too with Sally's Rayon, you just pull the whole strand through since the coil ID is 5mm, then just trim up the tails.
I keep looking at that coil... What 2 holes will you use? One top and a bottom or the the same level, top or bottom??? The tails are even on it so I think I would use the top or the bottom. Not sure tho until I try it. Using a top and a bottom might make it sit in there a little more sturdy... What do you think?
I just put in the 28g SS in one of mine and it's great so far. Going to use it in my other also. This tank is so easy to re-wire...
- Status
