Hey guys, wht mesh and wire do i need for the RSST, im not going sub ohm just LR setup, using mainly 70/30 PG/VG juices.
Thanks
Sent from my iVap using Tapatalk HD
Thanks
Sent from my iVap using Tapatalk HD
- Status
I run the same setup, it's great. At 1.5 ohms you can still fire on a regulated device with no problems. I have a mech but notice as the battery drains the throat hit an flavor reduce. I use it on a Provari and the voltage stays steady until the battery dies making the vape more consistent.
Woven Wire Mesh Stainless Steel 400 Mesh 6"x6" Filtration SS T316 Free SHIP | eBay
Buy two, get one free!! (That's what I did)
Thanks, i send an email to pbusardo asking him for the setup i need and he told me go for 500 mesh, and i found 5pc of 3x3 for 5 bucks, 50ft 28g kanthal for $3.50 and 50ft of 30g kanthal $3.50 so i have enough for now
Sent from my iVap using Tapatalk HD
mine works best with 400 mesh and 0.5x0.1 flat wire. also dont lose the tiny refilling hole cap, i lost mine and its been leaking in my pocket ever since
I'm using 70/30 pg/VG juice , that's why I was recommended to go #500 mesh.
For the hole cap you can try some small nylon screw they should work pretty good.
Thanks,
Sent from my Nexus 7 using Tapatalk 4
Have being using my RSST now for a bit less than a week, took me 5 builds to get it works as I liked some trial with diferent wires, i endup on a .9 ohm 3 wraps coil vaping close to what i like, but hell i need a bigger airhole, what drill bit should i use? I dont want something extreme big but bigger than is now,
Sent from my iVap using Tapatalk HD
Sent from my iVap using Tapatalk HD
I use a 500 mesh and 28ga Kanthal A1 Mix at 50/50 excellent wicking. I run coils around 1.5ohm
I also opened the air hole slightly and vastly improved the draw.
I also opened the air hole slightly and vastly improved the draw.
Manage to open my airhole, i use a 1/16 bit, Is much better now but I think i would be better just a tiny bit less,
Any one of you is using 1/16 airhole?
Sent from my iVap using Tapatalk HD
Edited, holy cow i made a new coil 2-3 wraps with 28g 500mesh now I'm getting a super vape, the hole is perfect with that coil,
Any one of you is using 1/16 airhole?
Sent from my iVap using Tapatalk HD
Edited, holy cow i made a new coil 2-3 wraps with 28g 500mesh now I'm getting a super vape, the hole is perfect with that coil,
Last edited:
I'm using a 1/16" air hole in my AGAT-2 and love it. for mesh I recommend Mesh Wizard.
I'm new to the Rebuildables as well
And have an aga t2 trying to find the best build
What is the difference between 400 and 500 mesh?
I use mostly 50/50 but also some 70/30
would I use different 400/500 for each or would one work better for both?
Also would you guys say the 1/16 air hole is very airy or just perfect?
And have an aga t2 trying to find the best build
What is the difference between 400 and 500 mesh?
I use mostly 50/50 but also some 70/30
would I use different 400/500 for each or would one work better for both?
Also would you guys say the 1/16 air hole is very airy or just perfect?
I emailer pbusardo about the mesh and he told me to use 500 in my 70/30 blend. also in one of his vide he do some test and found mesh 500 better for thin liquids and 400 for thicker,
For the hole if you are use to get the tight draw of a vivi nova you will found the 1/16 hole a "loose" draw, airy is not the correct term in this case because with a good coil you will get a huge cloud of vapor, airy is more like a draw with lot of air and less vapor
For sure my RSST is a loose draw now but the amount of vapor is so good now,
Sent from my iVap using Tapatalk HD
I a guessing what you are saying its not a loose draw but an easy draw
sounds great thank you
Sorry my bad English, yap i mean a easy draw,
LOL some of you need to play Tetris with my English sometimes
Sent from my iVap using Tapatalk HD
- Status
Similar threads
