mwa's 801 HV-Imeo/Atty Mod

[mwa102464]

Mwa102464’s 801 HV Atty Cart mod for GG users…!!!!

OK Everyone I found the ultimate way to fill and vape an 801-HV/Atty tonight.
1st. I took a Vapor king carto and removed the white top cap and removed the clear silicone grommet.
2nd. I trimmed the grommet very easily on all 4 sides so it fit right into the top of the 801 cart.
3rd. I took a piece about a ¼-3/8 wide and about an inch long piece of blue foam and twisted it and fit it through the grommet and left about a ¼ inch or so sticking out.
4th. I filled the entire cart with liquid using a syringe (just how I filled it) you can put in the grommet then drip through the hole and then put in the blue foam.
5th. I put this on my 801 HV Imeo Atty, with this much liquid in my cart and the way it drips the liquid does not burn and stays cool the Vape is the best tasting Vape I have come up with yet at high volts. Im sure it will also work @ 3.7v and on any 801. I just like using my #9 GGTS at 6v-7v
6th. THIS IS JUST INCREDIABLE AND ONE AWESOME VAPE YOU ALL HAVE GOT TO TRY THIS..!!!!

Good luck
Matt
MWA102464

 

[mwa102464]

I forgot to mention you can get like 3ml of fluid in this

 

[mwa102464]

OK maybe 2ml but still its unbelievable

 

[mwa102464]

If your using a liquid with a good amount of VG in it you dont even need the blue foam and get an even better vape with this,,,!!!!!!

 

[quasimod]

Cool, looks like a great idea. Have you posted this in the cart mod sub-forum? I haven't seen this one, but I don't read everything there.

 

[mwa102464]

not yet I wanted the GG people to see it first but might as well post it there thanks

 

[harpo]

Mwa102464’s 801 HV Atty Cart Mod for GG users…!!!!

OK Everyone I found the ultimate way to fill and Vape an 801-HV/Atty tonight.
1st. I took a Vapor king carto and removed the white top cap and removed the clear silicone grommet.
2nd. I trimmed the grommet very easily on all 4 sides so it fit right into the top of the 801 cart.
3rd. I took a piece about a ¼-3/8 wide and about an inch long piece of blue foam and twisted it and fit it through the grommet and left about a ¼ inch or so sticking out.
4th. I filled the entire cart with liquid using a syringe (just how I filled it) you can put in the grommet then drip through the hole and then put in the blue foam.
5th. I put this on my 801 HV Imeo Atty, with this much liquid in my cart and the way it drips the liquid does not burn and stays cool the Vape is the best tasting Vape I have come up with yet at high volts. Im sure it will also work @ 3.7v and on any 801. I just like using my #9 GGTS at 6v-7v
6th. THIS IS JUST INCREDIABLE AND ONE AWESOME VAPE YOU ALL HAVE GOT TO TRY THIS..!!!!

Good luck
Matt
MWA102464

Matt,
How did you get the grommet to fit inside the cart since it's designed to go on the outside of it? What size hole did you put in the grommet where the blue foam goes through?

 

[mwa102464]

Harpo,

The Grommet is the clear silicone Grommet from a vapor4life carto that I used, Just trim it on each of the 4 sides to fit tight into the cart and fit it snug, the hole is alreadt made in the vapor4life carto and just so happens to be the perfect size on the 801, use a piece of blue foam, thread it through the hole first and shove the grommet into the cart Harpo, This is one awesome vape because it holds a ton of fluid and it all stays cool and the Atty only pulls what it needs, ya gotta try this you wont use anything else after you do..!!!!

Regards,
Matt

 

[harpo]

Never mind. I had a brain fart. I thought you were talking about an 801 cartridge cap. There's a silicon cap in the bottom of 801 caps.

 

[harpo]

Why did you cut the grommet? I was able to put it in without cutting it.

 

[crashtestjeep]

looks good, Ill def be tryin this one, thanks!

 

[mwa102464]

Ya you can stuff the grommet in there Harpo but it lacks performance like this and is not seated in the cart properly, just a slight trim and a snug fit works best I have tried every way, if you like stuffing it in there go for its no big deal, I just like the perfect fit and it also makes it easier to remove and replace Harpo, just give it a try, especially with the HV/801 Atty it is the perfect amount of fluid to the Atty I feel and I get plums of vapor without over or under fludding..

 

[mwa102464]

You will like this Crash

 

[harpo]

How much of the foam do you leave outside the grommet?

 

[doots]

Looks nice will have to try this out.. thanks for the mod!

 

[harpo]

I found the hard tip carts won't fit snug in the HV atty but the soft tip ones do. Brilliant mod, works like a champ.

 

[mwa102464]

Harpo,

You can adjust it to where you like it, I let about a 1/4 inch or so hang out the end and wet it really good all the way through almost like priming the foam, if your using a really thick VG you almost dont even need the foam or just a smell little piece because the really thivk juces drips so slow, however I like a bit of the foam in mine like I said above

 

[mwa102464]

the hit feels like ice on this mod especially because all the juice doesnt get burnt up and stays cool, Liking that arent you Harpo

 

[mwa102464]

Harpo,

Also try cutting a longer piece of foam and letting it run down into the Atty danling soppy wet above the Bridge with a full cart and the foam going into the cart a ways, this works really nice also

 

[mwa102464]

Thanks doots glad ya like it...!!!