• This forum has been archived

    If you'd like to post a thread, post it here instead!

    View Forum

Nebraska Vaping

Status
Not open for further replies.

hawkizefan

ECF Guru
ECF Veteran
Dec 10, 2010
10,741
24,580
65
omaha
2000mah batts

There is a switch on the side, 3.0v or 3.6v. I have always used it on the 3.6v setting, but earlier if I switched it to 3.0v the light would turn green, switch back to 3.6v it goes red...

What brand of batts?
If you were on the 3.0 volt setting then maybe, but that long on 3.6 seems odd.
If they/it is a good quality batt I would question the charger. Who knows.
My aw's take about an hour on the pila after I've drained them to around 3.5.
I've been getting about 2 days off a batt on the provari. Granted, I'm hitting the bullet as much but still very happy with the time run of these batts.
Bottom line(and I'm really just getting this)...good batts...good charger=:D

I've been very impressed with the pila...wish it did the lifepos as well....
 

PittBoss

Vaping like a boss
ECF Veteran
Verified Member
Mar 27, 2012
11,961
1,591
Lincoln, NE
2000mah batts

There is a switch on the side, 3.0v or 3.6v. I have always used it on the 3.6v setting, but earlier if I switched it to 3.0v the light would turn green, switch back to 3.6v it goes red...

What brand of charger is it? If I'm not mistaken, the 3.0/3.6 setting is for setting the nominal voltage your charger is supposed to charge to. A pair of 2000mah batteries should only take 5-9ish hours to fully charge, depending on the charge rate (Average is probably around 400-500mah). At the slowest I have seen (250mah), it would take aroun 16 hours.
 

Jakersvape

Vaping Master
ECF Veteran
Verified Member
Oct 27, 2012
6,795
1,124
43
Lincoln, NE
What brand of batts?
If you were on the 3.0 volt setting then maybe, but that long on 3.6 seems odd.
If they/it is a good quality batt I would question the charger. Who knows.
My aw's take about an hour on the pila after I've drained them to around 3.5.
I've been getting about 2 days off a batt on the provari. Granted, I'm hitting the bullet as much but still very happy with the time run of these batts.
Bottom line(and I'm really just getting this)...good batts...good charger=:D

I've been very impressed with the pila...wish it did the lifepos as well....

Brand????? uhmmmmm......EF??? They were the ones I got from Plumes
 

Jakersvape

Vaping Master
ECF Veteran
Verified Member
Oct 27, 2012
6,795
1,124
43
Lincoln, NE
What brand of charger is it? If I'm not mistaken, the 3.0/3.6 setting is for setting the nominal voltage your charger is supposed to charge to. A pair of 2000mah batteries should only take 5-9ish hours to fully charge, depending on the charge rate (Average is probably around 400-500mah). At the slowest I have seen (250mah), it would take aroun 16 hours.

It's a trustfire tr-001 I believe.
 

Jakersvape

Vaping Master
ECF Veteran
Verified Member
Oct 27, 2012
6,795
1,124
43
Lincoln, NE
Here's a crappy pic of the batt

3uha3ugy.jpg


Sent from my DROID X2 using Tapatalk 2
 

PittBoss

Vaping like a boss
ECF Veteran
Verified Member
Mar 27, 2012
11,961
1,591
Lincoln, NE
I've been googling trying to find out what the settings are, but so far no luck

Joe has my charger now.....I let him borrow my Vamo to try for awhile....so he is charging the 3000mah battery. So far it's been just over 12 hours and it's still charging

Shouldn't be any reason one battery is taking that long. I threw a 2250mah bat on my charger (just the one) after dinner and the light turned green a little bit ago. It was drained to 3.5..
 
Status
Not open for further replies.

Users who are viewing this thread