New Genesis type atomizer by DID!
- Thread starter Jim Damianidis
- Start date
- th_trl_thread_readers 0
- Status
I received my Temon today. Solid 500 mesh wrapped with a 28 ga 1.2 ohm coil. This thing is awesome. Nice small size I can carry anywhere. Fill hole size is perfect to prevent a vacuum lock while chain vaping, while not allowing leaking if it tips over in my pocket.
Only one regret, without directions, it took me 30 minutes to realize there is a locking function.
Now how do I sneak another one into the house without the wife noticing?
Only one regret, without directions, it took me 30 minutes to realize there is a locking function.
Now how do I sneak another one into the house without the wife noticing?
Recieved some 30 awg and some 500 ss mesh yesterday. I have been using 270 mesh and 325 for my bobas with 32 awg.
I have to say the 500 is much much better. Wicking isnt an issue even with bobas.
Also i found the 30 awg much easier to set up as it burns right through those micro hotspots that usually are giving me the problems.
3/2 wrap on my P+ is awesome. Works out to 1 ohm and even works on my provari
The DID just got better
I have to say the 500 is much much better. Wicking isnt an issue even with bobas.
Also i found the 30 awg much easier to set up as it burns right through those micro hotspots that usually are giving me the problems.
3/2 wrap on my P+ is awesome. Works out to 1 ohm and even works on my provari
The DID just got better
Question guys.. I have a 5/6 wrap. 30ga w 400 mesh. It reads 1.5 got the provari @ 3.8. Its hittin weird so i took cap off and towards the top the juice looks like its bubbly. Kinda boiling. Dont remember seeing this before.. Whats that about??
Just cleaned/polished the brass contacts on the Paps and DID. Wow !!! What a difference, hitting so much harder and more consistantly with my new super DIDolicious 0.6 Ohm 2/3 coil
My coil seems to be getting a layer of dirt? Maybe carbon buildup? But its a new coil.. Is that normal?
it's normal (thick juice seems to make more crud). wanna see dirty, take a look at Tony's : http://www.e-cigarette-forum.com/fo...enesis-type-atomizer-did-243.html#post7767944
If you are truly concerned about flavor crossing over. I would pull the wick and re-oxidize it. Wire and all. Do a full rinse out of tank.
But why go through all of that every time unless you change out from something like Pluid. Just think of it in concentrations. You are talking about drops left behind after sucking all the old liquid out with syringe. You are adding 3ml of liquid. The old concentrations are down now by around 300%, Almost undetectable. Or at least for a couple of seconds if you just do a straight swap of juice. I take that time to do a dry burn and clean off.
Might not help, but that is how I handle my did.
Recieved some 30 awg and some 500 ss mesh yesterday. I have been using 270 mesh and 325 for my bobas with 32 awg.
I have to say the 500 is much much better. Wicking isnt an issue even with bobas.
Also i found the 30 awg much easier to set up as it burns right through those micro hotspots that usually are giving me the problems.
3/2 wrap on my P+ is awesome. Works out to 1 ohm and even works on my provari
The DID just got better
I'm right with you there. I'm on 30ga 5/6 wraps with 500 mesh right now. "even works on my Provari" says a lot... you've got it right.
Last edited:
Boiling is good. Plenty of heat and plenty of liquid. Vape away...
Last edited:
Individual results may vary, but I dry burn and clean my coil about every 3rd tank full. I've had a coil last me 2 months before I wanted to change it up. I've read of others have had one last 6 months. Also I found the flavor to come back after dry burning and cleaning.
- Status
Similar threads
