Take a look inside the battery cap, it should have a "-" meaning negative, so the "+" goes in first.
New iTaste SVD can't vape
- Thread starter bnorton
- Start date
- th_trl_thread_readers 0
- Status
Take a look inside the battery cap, it should have a "-" meaning negative, so the "+" goes in first.
WT when I push both + and - I get 1.9A shows on the display ... battery is 4.2, 3.0 v, 3.0 p
but still can't vape
but still can't vape
Last edited:
You are all wrong, he is experiencing a hard short.
Seeing as you don't know what to look for, this should be fun. Why do I have a feeling you really tightened down your device. You cant go too tight, as that brass colored dot in the middle of your top connection there, will ground out to the outsides of the connector, or 510 threads.
Try another device, and remember, only tighten so as to achieve a connection. Like a loose snugness, if that makes any sense...but not wobbly loose.
Seeing as you don't know what to look for, this should be fun. Why do I have a feeling you really tightened down your device. You cant go too tight, as that brass colored dot in the middle of your top connection there, will ground out to the outsides of the connector, or 510 threads.
Try another device, and remember, only tighten so as to achieve a connection. Like a loose snugness, if that makes any sense...but not wobbly loose.
Last edited:
No I put the tank on just enough to hold it in ...
so if it is a hard short what do I need to do? ...
it is a smok trophy v2 1.8 brand new as of today
the battery is IMR 18650 NP 1600 mAh
the battery is IMR 18650 NP 1600 mAh
The place I bought this from says that "The SVD should fire down to 1.2 ohm"
Well, it could be that center pin or a wire inside your device touching metal in your device.
I'm sure you have a rough idea of positive and negative, and how they need to sat separate, right? Well, that center pin up top is the pos, and it should be fairly raised. As for the device, unscrew the coil head and see if the coil is too far over to one side. Once you dig around more, this should be self explanatory to you.
No I don't have another tank ... I might have to just go to another shop tomorrow and see if they will help me ... I don't know if they will because I didn't buy it there ...
I vape 1.8 all the time on an SVD.
Pushing + and - together, you got 1.9 - that's correct, it's reading the resistance of the coil. And if it can do that, it should then vape!
Before, you said it was reading NON or 0.0 or something...
Battery is definitely button "up"...
Man, I hope you figure this out and it's something silly!
GL!
Pushing + and - together, you got 1.9 - that's correct, it's reading the resistance of the coil. And if it can do that, it should then vape!
Before, you said it was reading NON or 0.0 or something...
Battery is definitely button "up"...
Man, I hope you figure this out and it's something silly!
GL!
Well, if you get a resistance reading, but can't vape, something is shifting around.
I hope it is because right now my head is hurting ... lol ... when I hold the + and - I get 1.9v but when I go to vape I get a red flashing button and a 0.0v
I think the battery was in backwards and the tank was the problem. Always have several tanks to use -this is where backups can be really important when you need to troubleshoot problems. Have at least 2 of everything including chargers.
I am telling you something is messed up ... I just hope the other shop will help me ... if they do I will post what I find out tomorrow.
- Status
Similar threads
