I have had tanks where they will work on one battery but not another. Once you get more involved and rebuild it gets a little easier figuring out why.
New iTaste SVD can't vape
- Thread starter bnorton
- Start date
- th_trl_thread_readers 0
- Status
I have a V2 tank ... and it did the same thing as they Smok one ...
the V2 tank just went on my ego c battery
I have 3 tanks coming in the mail ... they are just not here yet ... I just got the iTaste SVD today
That sounds wrong. Voltage range on the SVD is 3.3v - 6.0v. I don't believe it can be set at 3.0v.
Hold the "-" button and the power button for 3 seconds until you see "U0" on the screen. Then hit the plus to move the voltage up until like 3.4v.
Wait for the screen to go blank. Try to vape. Let me know what it shows on your screen.
If it was a short, it should show "ERR" on the screen according to the manual.
Last edited:
I rebuild my own evod attys. When I have a short (a wire not clipped close enough, or touching the inside) it'll read 0.0. It has also happened a couple of times when an atty is under 1.9. I always hold my breath when I see 1.9 on the screen with a new atty cause I don't know if its gonna fire or not.
Sent from somebodys phone I found using Tapatalk.
on the screen I get 0.0A ... and no vape
if I hold the + and - now I get 0.0A before I was getting 1.9A
Okay, it definitely sounds like there is something really wrong here ... It might be the coil, it might be the device. When you go to the store with it, hopefully they will be able to figure out what the problem is. Have you heard back from the vendor yet? Will they exchange or replace it?
Perhaps this is the same issue:
http://www.e-cigarette-forum.com/fo.../409387-innokin-svd-problems.html#post9354415
"I have encountered a problem though. The SVD stopped detecting the tanks! It would read 0.0A (which refers to the resistance, I guess A is the closest character on the display to the OHM/Omega sign). I was really worried until I attached my favorite tanks a bit looser. It turns out that the o-ring under the connection in the 510 threaded seat on top of the device was squashed. I was pushing the connection post down as I screwed my tanks on. The same issue is common in the VAMO. I will post a link:
Low ohm problem with the Vamo - Electronic Cigarette Forums - Ecig Advanced"
The link didn't like to copy over. But it's basically the Vamo o-ring fix.
http://www.e-cigarette-forum.com/fo.../409387-innokin-svd-problems.html#post9354415
"I have encountered a problem though. The SVD stopped detecting the tanks! It would read 0.0A (which refers to the resistance, I guess A is the closest character on the display to the OHM/Omega sign). I was really worried until I attached my favorite tanks a bit looser. It turns out that the o-ring under the connection in the 510 threaded seat on top of the device was squashed. I was pushing the connection post down as I screwed my tanks on. The same issue is common in the VAMO. I will post a link:
Low ohm problem with the Vamo - Electronic Cigarette Forums - Ecig Advanced"
The link didn't like to copy over. But it's basically the Vamo o-ring fix.
The vendor told me to pull the pin in the tank ... I tried that as well
LOL Yes, that's when you lock the settings.
Yep ... sure have ... lol ...
Handy little feature
Thanks I need a little laugh here ...
I will let you guys know what I find out tomorrow ... if they will help me ...
THANK YOU EVERYONE for your time and help ...
If they want to earn your business, then they will try and help you. If they do help, then I would consider trying to buy from them every now and them in a show of support for their help. They know that if they help you, you will be more likely to recommend more people come to them. That is just good business.
I have an SVD that does the same thing with ego tanks. 510 tanks it works fine. I only use it as a back up. I use my Vamo V2 and a gripper as my everyday carries. Good luck. Hope it works out for you.
On a side note - I was in your area Thanksgiving time. Went to visit my wife's Aunt that lives in Elkhart...lol
- Status
Similar threads
