New Youde RTA the Bellus
- Thread starter mecca7979
- Start date
- th_trl_thread_readers 0
- Status
I decided to use the pre-rolled coils that came with it, which came out to .57, and some Japanese cotton. vaping at 35W and it is hitting like a beast, no leaks or gurgling. Had to adjust the coils a bit after getting them secured, as it was shorting out a bit touching the sides of the chamber. Once I got that sorted, it's running beautifully now. Great taste and more than adequate vapor production.
Last edited:
I did the same and it's vaping like a champ. I like it around 45-50 watts though, airflow hitting the bottom half of the coils.
Last edited:
I let my wife try my Bellus because it had some juice in it that she wanted to vape. That was two weeks ago, and I haven't gotten it back. 
All I can hope is she got me the black one for Christmas, because I did rather enjoy this tank.
All I can hope is she got me the black one for Christmas, because I did rather enjoy this tank.
Got my clone Bellus today from FT to go along with the two original I have now.
I already cleaned it though it came clean. The only way to tell them apart is clone has silver 510 center pin and original is brass. Also the top of the single coil adaptor is metal not plastic Haven't filled it up yet but see no reason why it shouldn't act any different then original Bellus.
$14.69 ea
FastTech - Gadgets and Electronics
I already cleaned it though it came clean. The only way to tell them apart is clone has silver 510 center pin and original is brass. Also the top of the single coil adaptor is metal not plastic Haven't filled it up yet but see no reason why it shouldn't act any different then original Bellus.
FastTech - Gadgets and Electronics
OK -Update on my clone - using two coils that came with the clone coming in at .38 ohms dual coils 2.5 mm dia.
I don't think this is a clone more likely - 2nds or blemish. I say this because the one I got is missing the large dot that aligns the larger one to know if the air flow is wide open or closed - really have to look to see how many holes are open/closed. Its a pain.
Black glass - I did get the one with the black glass pretty hard to see where the juice line is, think I'll be using the black glass solid in TC mode.
No extra glass you get some cotton.
NO other issues found! Works as good as my other Bellus though that missing dot thing I will have to fix.
Would I BUY IT AGAIN - not if I wanted only one though would consider it for two or more because of the cost factor $10.00 saving ea.
I don't think this is a clone more likely - 2nds or blemish. I say this because the one I got is missing the large dot that aligns the larger one to know if the air flow is wide open or closed - really have to look to see how many holes are open/closed. Its a pain.
Black glass - I did get the one with the black glass pretty hard to see where the juice line is, think I'll be using the black glass solid in TC mode.
No extra glass you get some cotton.
NO other issues found! Works as good as my other Bellus though that missing dot thing I will have to fix.
Would I BUY IT AGAIN - not if I wanted only one though would consider it for two or more because of the cost factor $10.00 saving ea.
Just put some 1.5 mm claptons in my Bellus, wicked it normal for the small coils, put the wick right to the bottom of the juice well... .33 ohms, 55-60 watts, it's good good good. No wick trimming, no leaks, better flavor and the little coils help out with airflow...
Just picked up a black one today at a local b&m. I'll probably put a build in it over the weekend sometime. Think I'm going to buy a black rx200 and some hg2's to go with it.
Also grabbed a couple spare tfv4 pyrex tubes and the dual coil rba deck. Probably play with that over the weekend as well, but that's for another thread.
Also grabbed a couple spare tfv4 pyrex tubes and the dual coil rba deck. Probably play with that over the weekend as well, but that's for another thread.
- Status
Similar threads
