New Youde RTA the Bellus
- Thread starter mecca7979
- Start date
- th_trl_thread_readers 0
- Status
just got mine, best tank I've used to date ^^ only thing I hate is the top fill, I get massive leaking from it =T also, the AFC ring does seal well, but its incredibly loose!
Try leaving a little air gap at the top when filling. I left a gap and no leaks, left a very small gap and had a slight leak. It is a damn good tank!
Besides a little air gap, when I put the top back on I'll screw it down until I just start to feel the rubber stopper hit, than flip it over as I give it the final half turn and while it's still upside-down I'll open the airflow. No leaks yet...
Thanks for the tips, but I just bottom fill mine =P The deck comes out easy without messin up the wicks, and lets me inspect the coils between juice fills anyways
Dual filling options... just one more thing to love about the Bellus!
On a side note, running mine on an Evic VTC Mini with a .35 ohm dual clapton build at 35 watts. It took only 80 puffs to drop the juice level from full to level with the bottom of the glass. She's a juice hog but I still love her!
Well after spending some time with this tank, and trying a few different builds, my conclusion is it really makes very little difference how long, or short the tails are. I had no issues with long tails, and no issues leaving them short. Still absolutely no leaking, when filling, leaving it on the side overnight, pocket carry.
Just my opinion, but what matters is the density of the wick, making sure you block the deck portion of the channels correctly. My latest build (pictured) is 26g, with short tails. I had to break out the old IPV3 tested at 117watts not even a hint of dry hits, I'm sure it would go a bit higher, but @.62 ohms, that is as high as the IPV3 will run it (voltage cap)
Just my opinion, but what matters is the density of the wick, making sure you block the deck portion of the channels correctly. My latest build (pictured) is 26g, with short tails. I had to break out the old IPV3 tested at 117watts not even a hint of dry hits, I'm sure it would go a bit higher, but @.62 ohms, that is as high as the IPV3 will run it (voltage cap)
Just got it and built it, tiny leak from the afc when filling, no big deal. Say hey to the youde family
X2
Mine will be here today along with my second MT.
HELP!!!
just bought the Bellus, but everytime i want to open the top cap for refilling, i turn out screwing off the chimney. n juice began leaking from the glass.
wat must i do to loosen the screw on the top cap so that its easier to take it off?
just bought the Bellus, but everytime i want to open the top cap for refilling, i turn out screwing off the chimney. n juice began leaking from the glass.
wat must i do to loosen the screw on the top cap so that its easier to take it off?
Don't crank the top cap down too tight, just snug it up, grip the the entire lower portion including the tank when your removing it, make sure the tank section is reasonably tight.
I've not had an issue with it.
Going through the same thing with gearbest right now. Let me know how it turns out.I've been patient so I don't want it to come off as the typical "gotta have it right now". I understand that shipping a tiny item thousands of miles away can hit some roadblocks. I do however expect a certain level of accountability from the seller. If I sold something and shipped it with no receipt by the buyer in the timeframe dpecified, I would do everything in my power to satisfy the customer and keep MY name in good standing.
I've gone 4 MONTHS waiting for a ten dollar package from Gearbest, emails/excuses back and forth. Finally went into a dispute with them via PayPal.
Done with China etailers. (Except maybe FT, maybe)
I would definitely be interested in one of your device's should you list it in the classys. I'm sort of waiting on a refund before I purchase anything else as that money is my budget right now. PayPal informed me that the dispute could take up to 30 days, and that's if they decide in my favor.
I ended up getting mine. Their tracking was absolutely useless. Took almost 4 weeks after shipping.
I could say "just be patient, it will show up", but it's up to the carriers and customs.
In the end it's worth the wait, damn good device. Perfect, no, but my favorite so far.
Thanks for the info. I'll try to be patient. Might just order another aromamizer rdta. It works great.
- Status
Similar threads
