Now why didn't I think of that... Hobby shops do sell those stuff in M2 sizes. EG: nuts, screws, insulators... Gonna see to it when my back's better...
I bet a power Burger will set your back right!
Non leaking aga-T version
- Thread starter madhero
- Start date
- th_trl_thread_readers 0
- Status
I bet a power Burger will set your back right!
Sadly my favourite kenna pluck morning radio programme got remove~
Oh really?? How long ago was that? It's been awhile since I last listened to radio...
Sent from my slipped disc using MRI.
upz this thread for e mad guru!!
I was wondering how long y're gonna wait to do something like this..
proud to have such a professional in-house modder.. from e the mesh mob to cactus mob oh, n of course, ninja's favorite MOB. =PPP
I was wondering how long y're gonna wait to do something like this..
proud to have such a professional in-house modder.. from e the mesh mob to cactus mob oh, n of course, ninja's favorite MOB. =PPP
Yeah. Ain't fun, innit? Losing control of the lower body when it 1st struck, in a major shopping centre is definitely not funny at all. I tell you that.
Sent from my slipped disc using MRI.
Last edited:
I hope u regained the use of some portions of your "lower body"... lol... Though not in a shopping centre. U'd most likely end up in Stomp.
Yups... Recovering and moving along nicely...
Sent from my slipped disc using MRI.
Sent from my slipped disc using MRI.
Check that your mesh is properly flamed, preferably to a dark orange glow. If it does glow again after the abovementioned step, nudge the coil (up or down, up to you.), and make sure your wick is not sticking to your coils. Pulse, pulse, pulse. Nudge. Pulse pulse pulse.
Hey guys another tip to share.
If any of you are looking for a small enough washer to fit, you can DIY it yourself, no need to look around for it so hard in hardware stores.
If you have spare CE4 or ViviNova heads, just remove the rubber 'condom' at the top and use the metal cap. I sanded mine down on one side till it's flat and just about 1mm sanding on the other side. After that i removed 1 screw from the AGA-T+ center post and used this DIY'ed washer for the middle screw.Just make sure the flat part of the 'washer' is at the top. Works and fits nicely, specially when i use the flat kanthal on it, no need to twist and turn so much to fit it in.
If any of you are looking for a small enough washer to fit, you can DIY it yourself, no need to look around for it so hard in hardware stores.
If you have spare CE4 or ViviNova heads, just remove the rubber 'condom' at the top and use the metal cap. I sanded mine down on one side till it's flat and just about 1mm sanding on the other side. After that i removed 1 screw from the AGA-T+ center post and used this DIY'ed washer for the middle screw.Just make sure the flat part of the 'washer' is at the top. Works and fits nicely, specially when i use the flat kanthal on it, no need to twist and turn so much to fit it in.
Hey guys another tip to share.
If any of you are looking for a small enough washer to fit, you can DIY it yourself, no need to look around for it so hard in hardware stores.
If you have spare CE4 or ViviNova heads, just remove the rubber 'condom' at the top and use the metal cap. I sanded mine down on one side till it's flat and just about 1mm sanding on the other side. After that i removed 1 screw from the AGA-T+ center post and used this DIY'ed washer for the middle screw.Just make sure the flat part of the 'washer' is at the top. Works and fits nicely, specially when i use the flat kanthal on it, no need to twist and turn so much to fit it in.
you have a photo of it?
got picture to show, a bit hard to imagine
Hey guys another tip to share.
If any of you are looking for a small enough washer to fit, you can DIY it yourself, no need to look around for it so hard in hardware stores.
If you have spare CE4 or ViviNova heads, just remove the rubber 'condom' at the top and use the metal cap. I sanded mine down on one side till it's flat and just about 1mm sanding on the other side. After that i removed 1 screw from the AGA-T+ center post and used this DIY'ed washer for the middle screw.Just make sure the flat part of the 'washer' is at the top. Works and fits nicely, specially when i use the flat kanthal on it, no need to twist and turn so much to fit it in.
i know what you mean =) the top coil only got hotspot but the rest all dont have right? then u humtum juice inside alr? i coil tighter at the top forcing it nearer to the positive pole, then drip some juice on it to let it oxidase the coil that it about done for me =)
I'll put up some pics once i am able to do close up shots on my phone's camera lol.
- Status
Similar threads
