Nuppin'
- Thread starter Spydro
- Start date
- th_trl_thread_readers 0
- Status
No movies for two weeks. I promise. Ima end up living in the basement if I don't stay the hell out of it
I hate you bassturds. Yes this little atty does vape amazing and yes ^ the squonk drain is off the chain. Best I've seen too.
You've got to learn to trust those that you know from past experience are trustworthy pard. I believed what you've said about the Odin... I just didn't and still don't want a 22mm atty on any of my Reos. Hope the Nuppin' works out very well for you... but if you decide to stay with the Odin's only you know where to reach me.
You've got to learn to trust those that you know from past experience are trustworthy pard. I believed what you've said about the Odin... I just didn't and still don't want a 22mm atty on any of my Reos. Hope the Nuppin' works out very well for you... but if you decide to stay with the Odin's only you know where to reach me.
True dat. I'm doing some side by side vaping right now. From an ease of build perspective, ODIN wins. From feed / drain perspective nuppin crushes. Aesthetically I like em both. vape wise, I like em both. Wicking ease goes to the nuppin. What it comes down to at this point is do I wanna retool? I'm strongly considering it
True dat. I'm doing some side by side vaping right now. From an ease of build perspective, ODIN wins. From feed / drain perspective nuppin crushes. Aesthetically I like em both. Vape wise, I like em both. Wicking ease goes to the nuppin. What it comes down to at this point is do I wanna retool? I'm strongly considering it
You're retooling wasn't my intent in my teasing you about trying one way back when. Was a spike to get you to do a video on the Nuppin's more than anything.
FWIW I have somewhere around 20-21 bf atty's for 9 Reos, and most of them are just collecting dust. In part because 5-6 of the Reos are also mostly just collecting dust since I settled on 3-4 ADV's some weeks ago and that is all I have been vaping since.
Those unused Reos are not lonely though... there's around 32-33 APV's altogether, their endless toppers, spares, supplies, etc all just collecting dust. These 3-4 Reos in use get it all done for me in spades, all I need for now.
Yes there will be a vid in the near future
. I want to get the right size Allen bit for my driver first At this point my attys way outnumber my mods. I'm down to 3 mods and 9 attys
Yes there will be a vid in the near future
At this point my attys way outnumber my mods. I'm down to 3 mods and 9 attys
Will be watching for the video.
ICYDK... you'll need a 0.9mm hex bit.
There's only like 27 now
Next you'll want everything "good" converted to torx!
I find the Nuppin easier to setup and maintain in every way compared to a BF Odin. I also wasn't happy with Nickel coils in the Odin. My Nuppins have only seen nickel coils and TP because I'm enjoying it so much better than a Kanthal vape. Running a different atty tonight with dual Ni coils and it's a pretty fine too.
I might kick myself for not getting more Nuppins while there's still a few to be got.
I am looking forward to the video Russ. Not being very good at tinkering has hindered me in getting this atty up and running. Your presentation and easy to follow instructions make it a joy watching your videos.
Decided not to chance whether Supe will resell his or not after he tries it... he's going to like it. So I ordered Nuppin' #3 before they are gone. But a #4 would also work for me if he does.
Will need to get another LP to run #3 on... only 2 of my 9 Reos are LP's. Either that or send the Mini to the spa (or some of the Woodies) for a haircut and/or 510 upgrade.
When I saw FB's post I ordered #3 as well. You never know when REO #16 will come calling.
Russ, glad you like the Nuppin, 
if you haven't already, play with height of the coil. These bad boys like a higher coil than most RBAs.
if you haven't already, play with height of the coil. These bad boys like a higher coil than most RBAs.
Huh? If you have a source for 2mm grub screws that use a torx driver, you'd better post a link!Next you'll want everything "good" converted to torx!
The Evil Rossum hatches a plan.
Step 1: Wait in his lair until a few days before Russ posts a Nuppin' video.
Step 2: Buy out all of Peter's remaining stock of Nuppin' atties to add to the 5 he's already got.
Step 3: Post them one at a time in the classies.
Step 4: Rake in obscene profits!
Last edited:
There's only like 27 now
Glad you like them Russ, they are great atty's for sure and will serve you well. I know that I find myself reaching for them more and more.
I like the fact that they vape great, very well made, will handle all kinds of builds, look good, and they allow my doors to slide up and down. I have considered replacing my 5 cyclone AFC's but just have not pulled the trigger.
I guess I better make up my mind pretty darn quick before they are all gone.
You better buy now my man. There ain't many left and I'm already getting PMs about where to get em
I like the "evil Rossum" moniker
Thank you my man. I will make a simple template to ensure that all my negative leads are the same length by pulling my current coils and measuring them prior to the vid. That way every build will be identical. I like identical
the template will likely be one of the Allen wrenches with the short side clipped at the exact place to trim the wire.- Status
