Nuppin'

[Papa_Lazarou]

Question for you Nuppinauts.

Anyone know what the o-ring sizes are for the atty? Ima place an o-ring order (hopefully one to end all ages) and want to make sure I've got these bad boys covered.

Plus, I lied - got another question. What size are the grubs (teeny little guys, ain't they?)?

Apologies if this has been discussed to death already.

 

[Rossum]

Answers are here:
pdib LIBRARY: tech/specs/info | Page 5 | E-Cigarette Forum

 

[Papa_Lazarou]

Thank you, sir.

 

[WharfRat1976]

Scored a Nuppin v2 in the classies today. Can't wait to get it and compare to the Odin...NUPPIN ME BAAABY...

 

[pauly3]

I too scored a Naval Brass AFC top cap for my new Woody!

It's Nuppin' but love for these bad boys!

 

[WharfRat1976]

I too scored a Naval Brass AFC top cap for my new Woody!

It's Nuppin' but love for these bad boys!

WOW, whole lotta NUPPIN goin on there.

 

[pauly3]

Ohh yes! 3 v1's and 3 v2's! Have several more Copper AFCs sitting in a drawer never been used!


- Pauly3

 

[Spydro]

3 of my 6 Nuppin's have new homes... IMO the perfect atty for the new Mech Woodvil's. Leaves 3 LP Grands that are having to get by with other atty's for now. I too have a lot of extras for the Nuppin's.

 

[TX Foilhead]

Nuppin V2 question. I tried the parallel single coil build from a few pages back and it works awesome so far. Issue is that on my v2 the hole in the center post runs 90 degrees to the holes in the deck. Made for some very interesting legs and resistance was a ways off of what I was expecting. Is there some way to adjust the orientation of the center post?

 

[WharfRat1976]

3 of my 6 Nuppin's have new homes... IMO the perfect atty for the new Mech Woodvil's. Leaves 3 LP Grands that are having to get by with other atty's for now. I too have a lot of extras for the Nuppin's.

Beautiful boxes!

 

[WharfRat1976]

Well, 6 builds later I landed on a Nuppin build that works for me. This is a 26g parallel around a 1.5mmID stuffed with KGD and mounted as high as possible without touching the bottom of the drip tip. It ohms out at .7 and as low as .5. The high coil creates big vapor and the Nuppin flavor is big. It took me about 5 builds to figure this one out. I am still figuring out the squonk to saturate the high coil. I have been quick bursting the squonk multiple times as when I do a long squonk I overflow it. Pics!

 

[Rule62]

Nuppin V2 question. I tried the parallel single coil build from a few pages back and it works awesome so far. Issue is that on my v2 the hole in the center post runs 90 degrees to the holes in the deck. Made for some very interesting legs and resistance was a ways off of what I was expecting. Is there some way to adjust the orientation of the center post?

Yes, you can turn the center post with a screwdriver. The 510 pin at the bottom of the Nuppin is slotted.

 

[BlueSnake]

Can someone show/tell/explain the difference/s between the Nuppin V1 & V2?

 

[TX Foilhead]

Yes, you can turn the center post with a screwdriver. The 510 pin at the bottom of the Nuppin is slotted.

Thanks, thought about that but didn't want to break something that I wasn't sure would move.

 

[TX Foilhead]

I believe the main difference is the V1 has a shelf around the bottom of the deck that the top cap and airflow ring sit on and the V2 does not.

 

[Filthy-Beast]

I think there are also some subtle changes in the 510 to make it easier to fabricate. Look here for more details pdib LIBRARY: tech/specs/info

 

[SteamStack]

How often does the maker sell a batch of these babies? Never know where to look for them.

 

[rudy4653]

How often does the maker sell a batch of these babies? Never know where to look for them.

No news on further production. Best bet is to keep an eye in the classies.

 

[WharfRat1976]

Dibs told me no plans for another batch currently. Obviously it's a limited market and well saturated.

 

[WharfRat1976]

Yes, you can turn the center post with a screwdriver. The 510 pin at the bottom of the Nuppin is slotted.

Using just my hands there is no way I can get my slotted 510 pin to move a nano inch. Just snip your neg side to 5/16"s and get it in the deck hole. I tighten my pos down first than lift it up to get my neg leads into the deck hole then tidy it all up...