Pdib adjusted the 510 pin on a bunch of nuppin before he shipped out so the later ones were all already adjusted out a bit.
Nuppin'
- Thread starter Spydro
- Start date
- th_trl_thread_readers 0
- Status
I found mine to be relative easy to adjust, especially when compared to a Cyclone center pin that required boiling and freezing to get it to move.
Just got the Nuppin so this is what I'm rocking. 0.6 ohms as you can see. 8 wraps, 2.0mm screwdriver, 28g kanthal and KGD cotton.
Anyone know of the airhole size? I don't have a way to measure at the moment, but I love this thing. I got mine from a user on this site. Thanks Olefolks, if you see this.
Anyone know of the airhole size? I don't have a way to measure at the moment, but I love this thing. I got mine from a user on this site. Thanks Olefolks, if you see this.
Just got the Nuppin so this is what I'm rocking. 0.6 ohms as you can see. 8 wraps, 2.0mm screwdriver, 28g kanthal and KGD cotton.
Anyone know of the airhole size? I don't have a way to measure at the moment, but I love this thing. I got mine from a user on this site. Thanks Olefolks, if you see this.
Danny, if you look at my Elvis killing build, you'll see where I turn the 510 to there the holes in the centerposts are closer to the wire capture holes in the deck. Doing that (turning the center post out about 1/4 turn makes the negative legs shorter
My man Rossum taught me that
Danny, if you look at my Elvis killing build, you'll see where I turn the 510 to there the holes in the centerposts are closer to the wire capture holes in the deck. Doing that (turning the center post out about 1/4 turn makes the negative legs shorter
My man Rossum taught me that
I'll have to try that, I was just too excited to mess around with anything and just build it haha
That dang allen key is small though. I've never liked them especially when building
Mine does same thing and Im not running an oring due to short 510 length. Does it on non reo mods too.
How the heck does one order a Nuppin'? I've seen it somewhere posted before, but I can't find it again, help, I'm so lost!!
Check the classies! One of mine is coming up soon!!!!!!!!!!!!!!
Pauly3
Sent from my iPhone using Tapatalk
Pauly3
Sent from my iPhone using Tapatalk
Chap by the name of pdib is the vendor, buuuuuut... he's sold out (it was a limited run).
Two options, then:
1) Look in the classies (here or elsewhere) - maybe post a "looking for" ad.
2) Wait for a second run by pdib. In the meantime, here's the thread where everybody (including pdib) talks about his gear...
http://www.e-cigarette-forum.com/forum/modder-accessories-supplier-forum/587492-im-thinkin-maybe-we-should-try-again-you-kids-should-behave-yourselves.html
Firing pin on Nuppin' is protruding a bit too much. Use a flat head and "screw" back into the atty base. This fixed mine plus an o-ring!
Pauly3
Sent from my iPhone using Tapatalk
Thanks Papa! I was afraid of that being the answer.
I did look at that thread too, searched for pdib posts...that's where I was running circles.
I'll keep an eye out for another run & check the classies.
I did look at that thread too, searched for pdib posts...that's where I was running circles.
I'll keep an eye out for another run & check the classies.
Or it's too short, I had to bring my center pins out more so I could use an o ring
Mine was out too much and caused juice to flow into pin and around pin filling up juice well and out over. Once I inserted the firing pin that stopped immediately. I always use o-rings for safe measures but that too prevents juice from spilling out if its thick enough. I use a 1.5mm for high PG and can get away with a 1.0mm for higher VG juices!
Pauly3
Sent from my iPhone using Tapatalk
Pauly3
Sent from my iPhone using Tapatalk
I am running a single 29 gauge at around .9ohms. i tried a 510 oring but no connection when completely screwed on. It did not come with a larger oring like the RM2. I tried the RM2 oring and it would not connection either.
Do you use a 510 oring or a larger diameter one like the one that comes with the RM2?
So ... question for all you Nuppin'nauts , as I mentioned earlier I am very happy with my current single coil 1 ohm build and have yet to try dual coils. My question is what is the biggest difference that you all find with dual coils over single coil as far as flavor, warmth, battery life, juice consumption? I am not a direct lung hitter looking for massive clouds but more warmth, flavor kind of guy with draw more towards tighter than airy. I am fighting the temptation to try a dual coils and have been hesitating as my current build is very satisfying and I'm afraid to take it off and try a different build and not get it as good , but you know how it goes, always looking for that extra 'something" which has become more and more difficult when you own a REO & Nuppin' with RxW wick! 
I have tried many dual coils setups, cyclone +AFC, Odin, RM4, RM5 Patriot, Apollo and the Nuppin, I just like singles better. Dual will drink more liquid.
- Status
