Does anyone know if the efest 18650 batteries on CCV site will work in a provari?
OFFICIAL: CyrstalClearVaping Information Thread..
- Thread starter cmdryker
- Start date
- th_trl_thread_readers 0
- Status
as long as you have the 18650 extended cap then yeah it will fit. The 18500 would fit with the regular cap.
Roger. What I meant to say, was that due to the fact that the efest's don't have nipple; would they fit the same as the AW 18650 in the extended cap.
I don't know how the Provari is set up, but I would think that there would be no problem that way...I usually have to extend springs and make the base wider on the units I buy to ensure good contact with very little moving around... just don't lengthen them so that they push the battery too hard into the positive post...
I hate to say this, but I am going to say no. The Provari positive connector does not sit low enough to connect with flat-top batteries. One of the few tube mods I have come across that doesn't. The nipple-top 18500 batteries will though.
There isn't a spring at the negative end of the Provari?
Either way, if you are quick about it you can put a blob of solder on the battery end to make it extend higher...(if you are not good with electronics, don't try it)
Either way, if you are quick about it you can put a blob of solder on the battery end to make it extend higher...(if you are not good with electronics, don't try it)
Last edited:
How long are the inner o-rings supposed to last on a tank? Mine is just barely weeping at 2.5 weeks... If I sit the my unit up it develops a little leakage in the connector... I rinsed out the tank in warmer to hot water at least 2 times before thinking about it...
Per pbusardo on taste your juice about the Efest 18650:
I received this battery from Crystal Clear Vaping for test. Not going to put a video together on this one, I’m just going to let you know what I came up with.
I’m no battery expert and actually hate recommending batteries. I really don’t have the proper equipment to test them. If I put them in my device and they work… terrific! And the more vape time the better.
I ran through a few charges on this and tested it in the ProVari.
How does it work in a mechanical? What’s the power curve? I honestly don’t know.
But I do know that I had no issue using it in the ProVari.
The AW IMR 2000 mAh battery from the original ProVari review gave me around 18 hours of vape time until shut-down.
The Efest IRM 2000 mAh battery gave me around 19 hours of vape time until shut-down.
Lot’s of room for error on this one, but bottom line, it appeared to be pretty equivalent to if not lasting a little longer than the AW.
answered my own question lol
I received this battery from Crystal Clear Vaping for test. Not going to put a video together on this one, I’m just going to let you know what I came up with.
I’m no battery expert and actually hate recommending batteries. I really don’t have the proper equipment to test them. If I put them in my device and they work… terrific! And the more vape time the better.
I ran through a few charges on this and tested it in the ProVari.
How does it work in a mechanical? What’s the power curve? I honestly don’t know.
But I do know that I had no issue using it in the ProVari.
The AW IMR 2000 mAh battery from the original ProVari review gave me around 18 hours of vape time until shut-down.
The Efest IRM 2000 mAh battery gave me around 19 hours of vape time until shut-down.
Lot’s of room for error on this one, but bottom line, it appeared to be pretty equivalent to if not lasting a little longer than the AW.
answered my own question lol
The eFests must stick out a bit more, none of the flat tops I have will work in my Provari. I would be ecstatic if the e's do.
Just to help Provari mini users. The eFest 18350 button top works great in the mini. I believe the eFests and AW are the exact same size for all sizes.
Andrew can tell you for sure, but I think that the Efest nipple top IMR's are the same length as the AW IMR nipple tops.
OK...so I put the used carto back on with the tank and it does not leak...so it was not the o-ring...looks like the new carto just slowly leaks and that is all there is to it...I am laying it down when not using and also taking horizontal hits!!! (with the leaky one)
Last edited:
That's cause you cut the lower rings when inserting a new carto, put a drip tip on carto before inserting the carto in tank, put a drop or 2 of juice on it , slide in not nicks to lower ring. those tops on cartos are razor sharp, cut my finger one day just putting on a drip tip.
be getting some nipple top efest 18650 like the one I sent phil b. , but to answer the question, don't have a provari, but sure flat top 18650 efest I got will not work. But my nipple top efest 18500 should work fine in the mini setup.
Last edited:
How long do Boge LR's typically last? (Resurrectors last me about a week on unregulated 4.2 device)
Thanks!
Thanks!
YES! I have both efests and a full size ProVari and as always the commander is correct.
Should have been here already, was told my order would get shipped before there dam week and half holiday.
Last edited by a moderator:
I would so love to have their work set up here.. seems they get off more then work lol..
Last edited by a moderator:
- Status
Similar threads
- Locked
- Locked
