Official ProVari 3 Thread - P3 *PART 2*
- Thread starter MonsterKenny
- Start date
- th_trl_thread_readers 0
- Status
They do darken up some with age and use
I need to compare it to my ring, can anyone share a close up of a Ti provari
Sent from my SM-N900T using Tapatalk
I need to compare it to my ring, can anyone share a close up of a Ti provari
Sent from my SM-N900T using Tapatalk
Oh not shiny but yea it is dark, i think the light effects Ti too much
Sent from my SM-N900T using Tapatalk
My two too!
Too two.
To too.
Tutu.
Desmond.
OMG, what just happened? [emoji102] [emoji54]
That's cool, thanks! I imagine it's the same for the Ti Procyon?
I'm on the fence over what my next ProVari is going to be. Ti military P3 or Procyon? If it's a Procyon, Stealth or Ti? Life is so hard. I want to wait until May for all the warranties on my P3's expire but the FDA is forcing my hand. I'm getting a Radius for Jackie this month.
On any of the Ti units that I have owned...
The Battery caps were Ti, But not the Beauty ring or P3 connector. They were Stainless.
Jim
Thanks for the info. I was just curious as ultimately, I would've found out when my perspective item arrives. I was sorta thinking along the lines of extra parts.
I never used the Ti end cap on my Ti mini ... it is still brand new in the box.
went with a Provarinati end cap on mine
went with a Provarinati end cap on mine
I have a question. I've been thinking about getting a Provari. I'd mainly use it at work where I kinda hafta stealth vape (I'm a paramedic working for a hospital). My 'normal' Vapes at home (or out and about) are either my REOs, or a rebuildable around 65w and 0.5 ohms. I was planning on using it with a kayfun mini v3. My other rebuildables i use on higher power stuff. My Kayfuns are usually between 16 and 26w. I'm planning on getting one of the stealth models, but I'm debating between the P3 and the Procyon. Which would you go with in my situation? Depending on the day and the device depends if I MtL or DLH.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Given the above, I'd say Procyon. Will provide you with a little bit more flexibility down the road. JMHO of course[emoji2]
Sent with my communicator by Tapatalk[emoji92]
Yeah, what Jim said...
I'm not sure if I even want a Procyon but it sounds like YOU should go with that one...
I would go with the Procyon with your specs. You might consider lowering your watts and raising your ohms for stealth vaping. The Procyon is a bit tall for discretion. The close-out P2.5 Minis and a KFM3 would make a good mate. You need at least two Provari. A Procylon and a Mini would give you the best of both worlds. Nothing wrong with the P3. I am rocking my first KFM3 rebuild on one. I recommend them all! Radius is another good choice for stealth. I have one paired with a Kanger Subtank Mini RTA that is my favorite this week. I go more MTL. .7 ohms @ 12 watts on the Kanger. KFM3 on the P3 @ 1.6 ohms @ 10 watts. YMMV, but you can't go wrong with a Provari.
My Kayfun is usually built to between 1 and 1.4 ohms. 'Stealth' is more for vapor production. Keeping it in my bag or cargo pants is fine, but I want a tube mod for that. lol. Hence, my interest in Provari.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Sage advice, Jim, for which I completely agree. The Procyon brings 50 Watts to the table along with the new, more efficient end cap. I am vapeing a Procyon Stealth as I type this and find it to be a superb mod that, like all my ProVape gear, gives a better vape than any of my 30 odd box modes. Also, less seams on the Procyon means it is easier to sterilise with a quick wipe of an alcohol pad.
- Status
Similar threads
- Locked
