On stockpiling after FDA deeming regulations
- Thread starter dcdozer
- Start date
- th_trl_thread_readers 0
- Status
I have the 34mm orchids. Fit perfect with the long chimney. I also have 27mm 5 pawns tanks. Fit perfect with the short chimney top.
The finned orchid caps are a direct fit also.
PC tanks for 50 cents to a buck a shot are a no brainer stockpile item. I have 20 of each and will double that soon.
Last edited:
Here's the compatibility list someone graciously posted on FT.
Atomizer parts compatibility list for Kayfun, Cthulhu, Silverplay, GT-T 2, Goblin etc.: FastTech Forums
Some parts on the list are discontinued and there are additional parts that work that I have tested:
All in one bell cap that can be filled like a pro-tank: $1.50 Replacement PC Bell Cap Set for Kayfun Lite Five Pawns - w/ 510 drip tip at FastTech - Worldwide Free Shipping
34mm replacement tanks: $4.06 Replacement Tank for Orchid V6 RTA Rebuildable Tank Atomizer (5-Pack) 5-pack - PC (polycarbonate) at FastTech - Worldwide Free Shipping
27mm replacement tanks: $4.30 Replacement Acrylic Tank for Kayfun Lite Five Pawns RTA (5-Pack) 5-pack - translucent at FastTech - Worldwide Free Shipping
Cloupor topped with a 27mm tank on a KFL base:
Atomizer parts compatibility list for Kayfun, Cthulhu, Silverplay, GT-T 2, Goblin etc.: FastTech Forums
Some parts on the list are discontinued and there are additional parts that work that I have tested:
All in one bell cap that can be filled like a pro-tank: $1.50 Replacement PC Bell Cap Set for Kayfun Lite Five Pawns - w/ 510 drip tip at FastTech - Worldwide Free Shipping
34mm replacement tanks: $4.06 Replacement Tank for Orchid V6 RTA Rebuildable Tank Atomizer (5-Pack) 5-pack - PC (polycarbonate) at FastTech - Worldwide Free Shipping
27mm replacement tanks: $4.30 Replacement Acrylic Tank for Kayfun Lite Five Pawns RTA (5-Pack) 5-pack - translucent at FastTech - Worldwide Free Shipping
Cloupor topped with a 27mm tank on a KFL base:
I've seldom shopped the b&m's. 3 times maybe, just to get 5 Pawns juice. The rest has been online.
Sent from my LG-V700 using Tapatalk
Have you found replacement orings for fill screws j large orings?
Sent from my LG-V700 using Tapatalk
Sub Tank Mini Maz. If you close off all but one small hole it is close to a Protank. Open it is much more airy. It comes with a RTA and is easier to build than the Protank.
Kanger SUBTANK-MINI clearomizer
Thanks Chanel !
Did you use it with PT2 heads as well ? Thoughts please if yes. I assume that's a picture of the RTA section. How did that work for you ? Could you get a satisfying MTL vape from that at 10-15 watts ?
@Mazinny , I am a Protank lover too but I am using STMs more and more. I have several. Although I have not tried the PT coils in one (yet), the RBA for the STM is very easy to build on. And as Chanel said, with the AFC closed down, it gives a MTL hit comparable (to me) to an AFC on a Protank (not closed down) . Perhaps slightly airier, but not enough to bother me.
Thanks. Any idea where i can get one cheap ( shipping included ). I'm not really buying anything else, so shipping cost cannot be spread among different items !
Just ordered some authentic STM bases as one of my clone TTM's was not making electrical contact.
I'll give you my thoughts.
After giving the STM high praise (a few posts back) for it's ability to use the PT2 heads, I now have to say that I'm not impressed (with that aspect only). The vape is fine. Very, very good as a matter of fact. The problem is that after vaping for a while, it starts to gurgle due to juice getting in the base. I believe it's getting in through the chimney (but I'm not sure).
I've tried pushing the top cap up to the STM top tube, and even put a small o-ring on as well. Still starts to gurgle after a while. Set it down for several minutes, pick it up and vape and it's fine, for a few minutes.
I got so tired of it that I finally broke out the rebuildable head, swapped out the coil it came with (.5 ohm I think) for one of mine, and am happily vaping away with a 1.9 ohm coil at 7 watts with nary a gurgle.
This thing is so much more efficient than the PT2 that I don't dare increase the wattage until I mix some lower mg juice. Even at 7 watts, it's hitting WAY better than the PT2 ever did.I'm still going to fiddle with using the PT2 coils at some point. Maybe some silicone tubing stretched over the STM top tube that would still allow the PT2 chimney to fit into it. It's worth a shot.
I got mine here. VaporBeast - Vaping Supplies, Electronic Cigarettes, E-Liquid Shipping is free with $35 purchase. Code yeahbaby gets you 10% off.
I just got 3 STMs from beast. Be aware the rba that came with them is the one that comes with the toptank which has smaller hole higher up the chimney.
I have 6 of these. No problems whatsoever, and the RBA is the V2 (bigger juice holes). Also top fill, just keep an eye on those little juice hole o-rings.
$9.84 SUBTANK Mini Styled BCC Clearomizer - 3.5ml / RBA coil head 0.5ohm / stainless steel + glass at FastTech - Worldwide Free Shipping
The juice fill hole o-rings
$0.80 Rubber O-Ring Seals for E-Cigarette (10-Pack) 12-pack - 4*1.8*1mm (OD*ID*T) at FastTech - Worldwide Free Shipping
Thanks, i haven't ordered from Fasttech in two years ! Time to use some of the money i have in my paypal account ( if i can remember my password lol ! )
I did not use PT heads. No need to. I am perfectly happy building on the RBA it came with as it is triple times easier to build (no fiddling with insulator and such)
I like it 100% better than the protank. With all but one small air hole closed I think it is pretty much the same MTL and much better flavor and ease of build.
Just watch for sales because like usual, it is yesterdays news now and can be found cheap.
$22.68 Authentic KangerTech SUBTANK Mini Clearomizer - 4.5ml / 0.5ohm (15-30W) at FastTech - Worldwide Free Shipping
Also another way to buy cheap, FT,
buy the base
$5.38 Authentic KangerTech SUBTANK Mini Air Flow Control Valve Base - silver at FastTech - Worldwide Free Shipping
and the rebuildable deck
$5.59 Authentic KangerTech SUBTANK Mini RBA Plus Coil Head - stainless steel at FastTech - Worldwide Free Shipping
and one of these
$1.68 Acrylic SUBTANK Mini Bell Cap - 39mm at FastTech - Worldwide Free Shipping
Maz
The RBA on the one Clnire directed you too has a screw that you use to remove the well (chamber)
The RBA I direcetd you to the well screws on and off
The RBA on the one Clnire directed you too has a screw that you use to remove the well (chamber)
The RBA I direcetd you to the well screws on and off
Thanks, so $22 for authentic and $ 10 for clone on Fasttech. I will get one of each i suppose.
Chanel, how would you compare your Taifun GT2 vaping experience with the STM rebuildable ?
I did not realize that. Thanks for pointing it out! That little screw can get lost so easily, fortunately I have spares. But in a pinch, it would be nice to not have to deal with it at all. Hum, yet another FT order?
- Status
Similar threads
- Locked
