Orion V2 roll call
- Thread starter tierrataz
- Start date
- th_trl_thread_readers 0
- Status
hahahahah give it a go bro and Vape while you hit those g forces, you might get a real good head rush!!!!!!
For anyone wanting a replacement cap to drill out or just for using drip tips the list is at vape pit, once it's calmed down a bit there will also be replicas of the original ones. If you choose to have them with a air hole it will be the same size but lower than the original http://web77.extendcp.co.uk/vapepit...ip-caps---list/page__view__findpost__p__63939
Let me know when those replicas are list worthy
Will do, but you lurk in the pit often enough, I'm sure you'll know when I do!
Hi guys, trying to get an Orion for the missus and just need to source where to stalk for the glass tanks.
Can somebody give me a headsup where to get glass tanks for the Orion?
Thanks all.
Can somebody give me a headsup where to get glass tanks for the Orion?
Thanks all.
You can get extra glass tanks on UKV by a member named Terry
Here's the link: http://ukvapers.org/Thread-Glass-ta...katana-list?highlight=orion+replacement+tanks
Wow, a US supplier of the Orion, nice! I know Vapist in the UK has them but is UK only. This will be great for people here. What's the deal w/ the Kir tanks too? Someone here said he was going to make them for the Orion.
Hey Guys,
I just got my Orion V2.1 and have popped 4 coils already. Any tips to avoid this, as I am ready to vape the hell out of it. lol... I am wrapping just like any other Genesis atty 3/4 wrap and it pops as soon as I hit the button on the top at the possitive screw. I have no problems with any of my ZEN's, ihybrid, Did ect.
Thanks,
Chris
I just got my Orion V2.1 and have popped 4 coils already. Any tips to avoid this, as I am ready to vape the hell out of it. lol... I am wrapping just like any other Genesis atty 3/4 wrap and it pops as soon as I hit the button on the top at the possitive screw. I have no problems with any of my ZEN's, ihybrid, Did ect.
Thanks,
Chris
The key words were pop at top positive screw, common problem for some. Make sure the nut on the positive post has at least two threads showing, otherwise, tighten the nut some.
Vabeach try these if you get no reading on your mesh:
1-tighten top nut till 1-2 threads show at top of stud.
2-reduce wire lead as much as possible. It can darned near touch.
3-don't use a fresh batt on set up.
4-if all above fails, try twisted wire.
1-tighten top nut till 1-2 threads show at top of stud.
2-reduce wire lead as much as possible. It can darned near touch.
3-don't use a fresh batt on set up.
4-if all above fails, try twisted wire.
Ok Thanks, I tightened it up so I can see at least 3 threads and I'll give it another go...
Last edited:
I had the hardest time on the Orion as well the first few set-ups compared to any other genesis, but... Its WELL worth it..
Also, there are varying opinions, but I've had the best luck with the positive lead between the washers, and wrapped about 3/4 of the way around the screw.
This is also the only genesis where I keep a paperclip in the wick to help keep tension when tightening the nut as it seems to pull the coil with it otherwise.
Also, there are varying opinions, but I've had the best luck with the positive lead between the washers, and wrapped about 3/4 of the way around the screw.
This is also the only genesis where I keep a paperclip in the wick to help keep tension when tightening the nut as it seems to pull the coil with it otherwise.
- Status
Similar threads
