My gold plated mirandus mod. Omne with a mephisto v2 and other with little boy
Post pictures of your high quality clones!
- Thread starter DaveSignal
- Start date
- th_trl_thread_readers 0
- Status
You go into the settings mode, then simply tilt the mod to the left or right to decrease or increase. It's a gimmick yes, but for how many times I actually change the wattage its much better not to have two extra buttons.
My gold plated mirandus mod. Omne with a mephisto v2 and other with little boy
Wow. That mirandus looks great! I love nice engravings. Where did you find it?
How do you like the new mephisto? I have a vapetech mephisto v1, which I think it great. I saw a review of the v2 by twisted420 and he said that the lower air holes on the v2 were sometimes causing juice to pop in his face while he was hitting it. It could have been his build though... do you notice this?
Last edited:
Oh, I see. So in lieu of a button menu navigation or a time-consuming provari-like deal, they use a tilt sensor to make menu adjustments. As long as it works, its a neat idea that is different.
4nine and magma.. i'm liking magma alot right now. the 4nine is ok, but i'm not liking the button so much. it's crunchy and sometimes it will not fire due to angle it's being pressed at. might have to take sand paper to the button later if it doesn't smooth out in next week or so.
I don't have a 4nine, but I have always liked the idea of the way the bottom switch has the cutouts on it. Its like a combination of the benefits of a recessed button, plus you can fire it as if it were not recessed. Sorry to hear its not working perfectly. I'm pretty sure that the authentic is a magnetic switch and so should be any 1:1 clone. I would check the switch to make sure the pin is screwed in all the way and everything is lined up correctly.
Last edited:
Got the mod from focal. And the atty from angelcigs. The v2 is great but i just need to find thebright build for it. Right now i have used it for experiments cause ofnthe airflow and post holes
This is my Stingray, manufactured by HCigar. It was one of my first mech mods. I actually haven't used it a while, but was looking for a smaller sized mech to use with my new Billow RTA and I think this works great! It is a good clone. It works as it should, it looks nice, and it is small. This Billow is great so far too!
hcigar taifun gt, and penny clone. both 23mm. huge, and draw is very tight. but the flavor is great.
I just built a Billow, posted a few minutes earlier, and it actually the first RTA I have used. I've only been using it for about 20 minutes, but it is pretty neat so far. I wonder how it compares to the Taifun clone? How many ml does the Taifun hold?
Last edited:
Basic Sting Ray X with Tugboat V2
https://scontent-a-dfw.xx.fbcdn.net...2_10205759300128312_5022364450706657591_o.jpg
https://scontent-a-dfw.xx.fbcdn.net...2_10205759300128312_5022364450706657591_o.jpg
Basic Sting Ray X with Tugboat V2
Looks great! What e-juice is that you are holding?
spec said 5 ml, but i haven't measured it. i have to vape it a little differently from my RDAs. lung hit is not very easy. i wonder if aqua v2 has better air flow. i like the idea of not having to keep drip, but the air flow is too narrow on gt. i haven't even cleaned my kayfun lite plus v2 or Sat22 yet. and i heard they have even smaller air holes.
You should try the Billow from Eciggity that I posted above. It is a lung-hitter, although more restrictive than many of the cloud chasing RDAs. Its kind of like a Magma. It has been working perfectly for me so far. It is very good quality, manufactured by EHpro.
Steel Punk Slug with a 454
sweet. I wish my slug was copper, but I got mine before the copper was released. How is the 454 working for you? I have a 454 clone that one day I was rebuilding with twisted wire and was cranking down the positive post and the post started spinning. I thought it was an issue with the clone, but I have since talked to other people with authentic versions who also have spinning posts. I am debating getting another one. But then I think that there should be a v2 on the way sometime soon.
I haven't had any issues with it but I don't drip that often with it. It's tough finding copper anything to go with the slug locally here in Canada to match this thing. I'm thinking of either a squape or a fogger.
I love the slug. It's the very first clone that I've purchased. Everything else I have is authentic. I haven't put it down since I bought it. That says a lot for this mod as I have in rotation: a turtleship, provari mini, stingray and a nemesis.
The only downside to the 454 is the pain in the a## that it is to build but they all have their issues I guess. So far, I've tried the orchid, T5 and a big dripper on this mod and aside from the color mis-match, the big dripper is amazing on it.
The color doesn't need to match. The slug isn't one of those 22mm mods for a hybrid look. Its a unique form factor that works with pretty much anything you put on it.
All the recent slug posts made me want to get out my slug. This is another picture. I like the look of the copper version, but this brass slug with copper pins still hits very hard. I can't imagine the copper being more powerful. I've got an Ivogo Onslaught on it. I like the tri-coil onslaught. It works great with the low resistance builds that I put on it. I've had a tri-coil 24g build on it for awhile. I didn't rebuild it, or re-measure it, but I think it is around .15 ohm, same as my stillare v3. It makes a lot of vapor. I like the top-cap it comes with, but I think its even better wide-bore. I've got a fusionsmods cap on it right now and it is working great!
'Females buy purses to match their shoes. The same can be said for wanting a copper rba to match the copper slug.'
- Status
