What size is this o-ring? I think this solution would work great with my first generation ERA's.
RBA (Reomizer) build photo tutorial
- Thread starter juicejunky
- Start date
- th_trl_thread_readers 0
- Status
What size is this o-ring? I think this solution would work great with my first generation ERA's.
Look here: http://www.e-cigarette-forum.com/forum/reos-mods/161169-reo-measurements-parts-terminology-5.html#post7406429
for all those needing an o-ring for your catchcup, to prevent the ERA from bottoming out. check your local home depot
size is 7/16-9/16 #13 fits reo grand catchcup perfectly
Forgive me, I am a noob to ECF and REOs. Where can I get the reomizer? I have looked on the website and didn't spot it. Thanks in advance.
reomizer has been discontinued but you may be able to get one if you PM redeyedancer (Rob)
Wow. I must have gotten the last one. I haven't even taken it out of the plastic bag yet... Now I hesitate to open it. Maybe it will be like rare comic books
Thanks for the photos.
I ended up with 1.7 on my first try. It looked a little like the chain link at Daytona but vapes like a champ!!
I ended up with 1.7 on my first try. It looked a little like the chain link at Daytona but vapes like a champ!!
i had a pair of 2.75 reading glasses and a bright light
i used an eight inch drill bit and could go a little smaller cause it uncoils a bits when your done.
the vape and flavor of a new coil(broken in a bit) is just great.
i used an eight inch drill bit and could go a little smaller cause it uncoils a bits when your done.
the vape and flavor of a new coil(broken in a bit) is just great.
I am using the A7 and have a question:
What O-ring in the well???? I have never used one, wouldn't know where to get one, and wonder what the heck it is for? My A7 works just fine and I don't have a silly O-ring
What O-ring in the well???? I have never used one, wouldn't know where to get one, and wonder what the heck it is for? My A7 works just fine and I don't have a silly O-ring
I am using the A7 and have a question:
What O-ring in the well???? I have never used one, wouldn't know where to get one, and wonder what the heck it is for? My A7 works just fine and I don't have a silly O-ring
Val, you don't need an O-ring for the A7 or any rebuildable except for the reomizer.
When adding the 0-ring to the Reomizer, will i need to adjust the center post at all?
Nope. The center post should be fixed at a good height and need no adjustment. The o-ring will compress and does not interfere with the contact of the center post.
Depends on what kind of wicking material you are using but basically the answer is the same, whenever you notice an unpleasant change or drop in flavor. Until then, why fix what isn't broken
With cotton wicks I usually know the center of the wick has burnt through when I have to squonk with every other hit. I usually end up replacing them every 4-5 days, more often if I vape while extremely busy and forget to squonk a few too many times or not realize the bottle has emptied. Hemp wicks last a few days longer. My coils at 1.4 mm diameter are pretty tight and probably more prone to burning wicks.
I would think that silica would last as long as the coil.
I would think that silica would last as long as the coil.
how does the diameter of a coil affect the vape?
my coil was 1.7 but the loops seemed a little big, the vape has tailed of a bit
my coil was 1.7 but the loops seemed a little big, the vape has tailed of a bit
- Status
Similar threads
- Locked
