Single coil RDA with adjustable airflow recommendations

[RuDawg7890]

Hey, you're right...this is EXACTLY what I am looking for. Thanks!

Please let me know if you find one in stock!
After suspectK posted, I looked and they were in stock in two places.
Read this thread http://www.e-cigarette-forum.com/forum/rebuildable-atomizer-systems/538555-magma-rda-paradigm-3.html
and after I finished reading, both places out of stock!!

 

[rrayda]

Magma Atomizer by Paradigm Modz

I got two clones recently, and they are both solid..$35 each.

Where did you get them?

 

[islandgirl305]

Aga-t3 best single coil atty
This is with ribbon wire , works with anything though

Good luck

 

[ronpaek100]

I'm looking for some recommendations on a new RDA. I want:

1) Single coil
2) Adjustable airflow
3) Airflow NOT set up for multiple coils only (I like single coils and a tight draw)
4) Relatively easy builds (no falling apart when screws are loosened, etc.)
5) Preferably threaded assembly vs. o-ring compression fit OR a good o-ring fit.

I'm currently running an IGO-L with a 28 gage micro/cotton setup around 1.5 Ohms. I use a Provari, so much lower resistance than this is not where I want to go (pretty much eliminates multiple coil builds with the 28 gage wire). The IGO-L is nice and holds together fine with the o-rings, I'm just ready to try something else out.

Some context: I recently purchased an Optimus RDA from SmokTech..it's a great idea but won't stay together in my pocket due to the ill-fitting o-ring assembly style. It's probably just a cheap atty (it was cheap).

Does such a thing exist?

You should get a Quasar

 

[rrayda]

You should get a Quasar

Easier said than done, unfortunately. It does look nice, tho...

 

[blueGrassTubb]

I should have elaborated. The Igo-w has dual air holes, I only mentioned it to reference the tight O-ring. Might be better to check out the Igo-L as it only has one hole, but I would imagine has the same o-ring setup.
IGO-L Rebuildable Atomizer

Sent from my iPhone using Tapatalk

Some people complained about the looseness of the Igo-L cap, but, as with my iGo-W, I have to have the atomizer attached to a base in order to get it off.

 

[rrayda]

Some people complained about the looseness of the Igo-L cap, but, as with my iGo-W, I have to have the atomizer attached to a base in order to get it off.

My IGO-L is a little loose, but I think the larger diameter makes it more stable. It'll only come off if I grab it in my pocket by the cap. Good enough!

 

[HazMatt]

The Cyclone+afc looks like a winner to me. Are there any single coil RDAs with afc that are smaller in diameter?

 

[el Jexican]

I have the Atomic and Cyclone and can say that hands down the Atomic is the better choice, and I run it exclusively in single coil mode. Not saying that the Cyclone is bad because its a great little atty that I run in the Reo.

 

[treehead]

I'm looking for some recommendations on a new RDA. I want:

1) Single coil
2) Adjustable airflow
3) Airflow NOT set up for multiple coils only (I like single coils and a tight draw)
4) Relatively easy builds (no falling apart when screws are loosened, etc.)
5) Preferably threaded assembly vs. o-ring compression fit OR a good o-ring fit.

I'm currently running an IGO-L with a 28 gage micro/cotton setup around 1.5 Ohms. I use a Provari, so much lower resistance than this is not where I want to go (pretty much eliminates multiple coil builds with the 28 gage wire). The IGO-L is nice and holds together fine with the o-rings, I'm just ready to try something else out.

Some context: I recently purchased an Optimus RDA from SmokTech..it's a great idea but won't stay together in my pocket due to the ill-fitting o-ring assembly style. It's probably just a cheap atty (it was cheap).

Does such a thing exist?

The IMMORTALIZER! I have one on it's way.

 

[DeadbeatJeff]

The Omega clone is what I've been using. Can be set to single coil using the single airhole. Adjustable airflow, has the rubber o-ring fit to the base. Mine's has been working perfectly. Can twist the airhole closed if I'm carrying it around and it won't leak.

I have this as well, and I HATE it

not the performance, the building. the walls on the well are just too high and it's a major PITA to build

 

[Pamailman]

I have an Origen v1. It has dual sets of 3 air holes for setting up dual coil but also has a separate single set of 3 holes for single coil builds. Good size juice wells below the deck. The version 2 has a shared well so it would work better with a single coil. The o rings really hold this thing together. I'll load it up and as long as you didn't flood it you are good to go. I throw mine sideways in hoodie pocket all the time with no leaking.