Ok...are you being silly now ? Dont make me waste another hour trying to set up a PO Box in France.
Even if I did, I cant read French so I would end up marking it return to sender.....
retour à l'expéditeur
SM V3 Semovar VS Provari
- Thread starter SissySpike
- Start date
- th_trl_thread_readers 0
- Status
retour à l'expéditeur
Well, that was easy. First ever rba set up. 1st roll was 3.0ohm so took a couple of twists off to get it to 1.9ohm. Topfilled it as wasn't sure about the fill hole yet. Anyway here it is, KayFTun 3.1 clone on a Semovar and confirmed working.
View attachment 281319
View attachment 281319
Last edited:
in hybrid mode careful with the topfilling or any flooding will now go directly into the semovar 510 connector and not the collector plate you removed - wouldnt want to see it give up the magic smoke
Thrasher" data-source="post: 11514235" class="bbCodeBlock bbCodeBlock--expandable bbCodeBlock--quote js-expandWatch">Thrasher said:
How will it flood differently if you top fill, vs using the fill hole?
The kayfun's are based on positive and negative pressure. Top fill will create more positive pressure when putting top back on, with out tipping it upside down and letting that pressure release. If you use the bottom fill screw, there can be a large air bubble, but the air pressure isn't as high as when you top fill.
if it is in hybrid mode think of it like this, using the fill valve you have to turn to unit upside down meaning nothing can flood into the chamber from the pressure of squeezing the bottle all that comes out is air.
when the top is open you have broken the vacuum that keeps the juice from flowing into the chamber.
when the top is open you have broken the vacuum that keeps the juice from flowing into the chamber.
yes i have, go into the offline menu and readjust the power or voltage within range.
when I first got it i used VV for a while then switched to VW instant E3 as the wattage was too low for the resistance and was trying to fire at like 2.8 volts
what this means is whatever mode you are using the resistance + setting is outside the fire range of the device. in my case i had to go in the offline menu and turn up the wattage to about 6 then turn it back on and it fired fine.
you may also need to adjust the center pin as it will also say this if no contact.
E3:
It is impossible to hold the level of output voltage / wattage. This error can be caused if
the output power you have set up passed the voltage range of 3V-6V with the atomizer resistance
you are using.
It will be shown too if you are passing the wattage range of 3W-15W.
To fix it adjust your setup in the menu.
This error will mostly be shown if the atomizer has no contact to the Sëmovar. The electronic part
thinks at this moment the resistance of the atomizer is too high.
when I first got it i used VV for a while then switched to VW instant E3 as the wattage was too low for the resistance and was trying to fire at like 2.8 volts
what this means is whatever mode you are using the resistance + setting is outside the fire range of the device. in my case i had to go in the offline menu and turn up the wattage to about 6 then turn it back on and it fired fine.
you may also need to adjust the center pin as it will also say this if no contact.
E3:
It is impossible to hold the level of output voltage / wattage. This error can be caused if
the output power you have set up passed the voltage range of 3V-6V with the atomizer resistance
you are using.
It will be shown too if you are passing the wattage range of 3W-15W.
To fix it adjust your setup in the menu.
This error will mostly be shown if the atomizer has no contact to the Sëmovar. The electronic part
thinks at this moment the resistance of the atomizer is too high.
Last edited:
if you do 3 clicks and it says "on" that means you are turning it "ON" it was already off. (or offline)
it will only show you the choice you can choose not what mode you are already in.
it will only show you the choice you can choose not what mode you are already in.
^I like that. Does it do that when current is too high? Or does it also do it when you have a high resistance, and you're at a higher watt setting than the voltage range?
I was confused with the variable pvs I have. I use 3ohm cartos, and I thought I was getting 9 watts on the mvp..until I measured it. The placebo effect is a strong thing, cuz I swore it was able to go higher. It would cut out at 5volts, ~4.86 under load. The itastes also just give you a low voltage when you have a low resistance coil. That is the confusing part to me. It won't feed more than 5volts, but it will give you less than 3. Of course, once I measured it, I notice. Oh how glorious the mind is..
Edit: I guess you touched up your post a tad while I was typing..nvm thrasher
I was confused with the variable pvs I have. I use 3ohm cartos, and I thought I was getting 9 watts on the mvp..until I measured it. The placebo effect is a strong thing, cuz I swore it was able to go higher. It would cut out at 5volts, ~4.86 under load. The itastes also just give you a low voltage when you have a low resistance coil. That is the confusing part to me. It won't feed more than 5volts, but it will give you less than 3. Of course, once I measured it, I notice. Oh how glorious the mind is..
Edit: I guess you touched up your post a tad while I was typing..nvm thrasher
did you adjust the cneter pin and make sure it is contacting the atty? the 510 does adjust.
i just have to check........ are you using power or voltage mode? adjusting the wrong one wont make a difference.
i just have to check........ are you using power or voltage mode? adjusting the wrong one wont make a difference.
Last edited:
This, plus to use offline mode, remove the atty and turn it on.
"This error will mostly be shown if the atomizer has no contact to the Sëmovar. The electronic part
thinks at this moment the resistance of the atomizer is too high"
beyond that wait to see what C9 has to say. i dont know, so far every error for me has been user fault and went away using the manual.
just one more quick try, take the topcap off, screw on an atty then take some nedlenose and make sure the 510 pin is screwed up against the atty
Last edited:
- Status
