CAL-H V2 - BF version
Introduction
Except the ERA Hornet available now, there are not a lot of solutions for us Reo Mini users, when talking about a rebuildable atomizer (rba) that can fit directly without adapter or tweakings....
The german atty Surface is apparently coming out from the pre-order vaults since October 2012, but beside these two attys, nothing else seems to exist.
After some talk with Aniki, the mastermind behind Animodz, he modified it's best selling rebuildable atomizer (the Cal-H V2) to use it directly with a bottom feeder. And here it is !
Some sort of review
Delivered in a nice black pouch, inside there's the atty and a small 3ml empty bottle. There is also a small plastic bag (with dogs printed on it) containing some silica mesh and wire to recoil it.
Recoil yes, because it comes right of the box ready to vape, as it's already coiled (mine was at 1.5 ohm and very nicely done).
In fact I was so impatient to try it that I didn't take the time to make a picture of the clean coil, so you'll have to cope with my 3 days of use coil, sorry guys...
OK so let's put some good juice in it, two squonks on the bottle to be sure to wet the whole coil assy, and voila, I overflow it
Surprisingly after drawing for the first time on it and obviously gurgling, my second draw was not gurgling at all, all the juice went gently back in the bottle.
In fact, it's not so important if you sqonk too much with it, as after the first draw that gurgle, the second is already near silent. Way better than with my usual 510 or IKV atties...
Oh man this puppy goes well, really well. Tastes nice also. I'm vaping at 70 PG-30 VG, but the smoke is dense.
At 1.5 ohms the throat hit is present and pure. I'm impressed.
To be honest, because I'm playing more with Genesis and RBA attys, I had let my ReoMini aside for a while.
But I'm rediscovering it with this atty, seriously.
I like dripping but never coped with the hassle of dropping some juice every 3 minutes and that's why I had chosen the Reo.
But as RBA became the new trend, it was a pity that almost nothing exist for the Mini until now
Now let the pictures talk
Normal Mode (with lower ring)
Shorty Mode (without lower ring)
Close-up to see how it fit nicely inside the MINI cup
The atty itself
Another close-up to see how it fit nicely inside the MINI cup
Sorry for the not new resistance and the too much sqonk applied
Close-up to see the teflon plate and the screws
The three parts composing the Cal-H V2 - BF
Close-up of the Teflon deck without the coil
BTW, a little bird told me that some have already been shipped to a shop in USA....
- Dimensions
- Height: 32mm - Diameter: 12mm
- Height: 27mm - Diameter: 12mm, in Shorty Mode (without the lower ring)
- Aluminium (food quality prescription)
- Deck in Teflon
- Brushed version
- Unscrewable and interchangeable lower ring
Introduction
Except the ERA Hornet available now, there are not a lot of solutions for us Reo Mini users, when talking about a rebuildable atomizer (rba) that can fit directly without adapter or tweakings....
The german atty Surface is apparently coming out from the pre-order vaults since October 2012, but beside these two attys, nothing else seems to exist.
After some talk with Aniki, the mastermind behind Animodz, he modified it's best selling rebuildable atomizer (the Cal-H V2) to use it directly with a bottom feeder. And here it is !
Some sort of review
Delivered in a nice black pouch, inside there's the atty and a small 3ml empty bottle. There is also a small plastic bag (with dogs printed on it) containing some silica mesh and wire to recoil it.
Recoil yes, because it comes right of the box ready to vape, as it's already coiled (mine was at 1.5 ohm and very nicely done).
In fact I was so impatient to try it that I didn't take the time to make a picture of the clean coil, so you'll have to cope with my 3 days of use coil, sorry guys...
OK so let's put some good juice in it, two squonks on the bottle to be sure to wet the whole coil assy, and voila, I overflow it
Surprisingly after drawing for the first time on it and obviously gurgling, my second draw was not gurgling at all, all the juice went gently back in the bottle.
In fact, it's not so important if you sqonk too much with it, as after the first draw that gurgle, the second is already near silent. Way better than with my usual 510 or IKV atties...
Oh man this puppy goes well, really well. Tastes nice also. I'm vaping at 70 PG-30 VG, but the smoke is dense.
At 1.5 ohms the throat hit is present and pure. I'm impressed.
To be honest, because I'm playing more with Genesis and RBA attys, I had let my ReoMini aside for a while.
But I'm rediscovering it with this atty, seriously.
I like dripping but never coped with the hassle of dropping some juice every 3 minutes and that's why I had chosen the Reo.
But as RBA became the new trend, it was a pity that almost nothing exist for the Mini until now
Now let the pictures talk
Normal Mode (with lower ring)
Shorty Mode (without lower ring)
Close-up to see how it fit nicely inside the MINI cup
The atty itself
Another close-up to see how it fit nicely inside the MINI cup
Sorry for the not new resistance and the too much sqonk applied
Close-up to see the teflon plate and the screws
The three parts composing the Cal-H V2 - BF
Close-up of the Teflon deck without the coil
BTW, a little bird told me that some have already been shipped to a shop in USA....
Last edited:
thanks.
