Smallest Mech Mods

[HeiSINberg]

I've really been enjoying my 2 4nine mods lately and now I want a 3rd mod that is small in 18650 mode. I have other mechs but after using the 4nine on the go it just fits me and my needs. So my question is what other mechs out there are small only in 650 mode?? Post pics if you have them!

Sent from my SCH-I545 using Tapatalk

 

[icebat]

Have you heard of Fortune mods? Todd, and safer vapers have a video on it. Probably will be hard to get your hands on one though.

 

[alkaiser]

xxix/surfrider are pretty small in 18650. not as small as the 4nine, but pretty small. it uses a similar hybrid connector

 

[HeiSINberg]

Nope, I will look through todds videos though thank you. I wanted a smaller copper mod. I have a penny mod and I dont really like how big it is. The top and bottom cap could of been slimmed down a lot.

Sent from my SCH-I545 using Tapatalk

 

[HeiSINberg]

xxix/surfrider are pretty small in 18650. not as small as the 4nine, but pretty small. it uses a similar hybrid connector

I was actually looking into them, they still have the pre-orders going on. I could never find the measurements for it but it did look somewhat small.

Sent from my SCH-I545 using Tapatalk

 

[alkaiser]

i measured mine and it is 3.25in/83mm in 18650

to give reference, the nemesis is about 4.25in/92mm

 

[HeiSINberg]

Wow! That is pretty small, I wanna measure my penny mod to see what it is when I get home. I think I might off the penny soon for the xxix or surfrider.

Sent from my SCH-I545 using Tapatalk

 

[HeiSINberg]

The penny mod is a hair under 4 inches, and I mean a hair. I took a pic to show it against the 4nine. I think the xxix or surfrider is honestly my best bet. I would of gotten the copper 4nine but I didnt have the money when they did the short release of them.

Sent from my SCH-I545 using Tapatalk

 

[bsoplinger]

i measured mine and it is 3.25in/83mm in 18650... to give reference, the nemesis is about 4.25in/92mm

There's a math error here somewhere. 1 inch = 25.4 mm. Which means that if the Nemesis is an inch taller it must be 25 mm taller, not 9 mm. Did you by chance mean 3.95 vs 4.25? Or have one set (metric vs English) wrong? Because I can't convert the mm to inch properly either.

Sent from my Nexus 7 using Xparent Purple Tapatalk 2

 

[alkaiser]

oops, definitely an error. i meant about 3.6 in...no idea why i put 4.25. the nemesis measured was also in hybrid mode

 

[HeiSINberg]

So does that mean the xxix is still 3.25 inches? Or taller?

Sent from my SCH-I545 using Tapatalk

 

[alkaiser]

i measured the nemesis incorrectly on the inches side. the xxix is accurate.

 

[HeiSINberg]

i measured the nemesis incorrectly on the inches side. the xxix is accurate.

Awesome! Thank you so much. I put my penny up for sale, hopefully someone will snag it up.

Sent from my SCH-I545 using Tapatalk

 

[Portertown]

NANOS | Nanos Single tube | mmvapors.com

Check out the new Nanos mod from MMVapors(builders of the Poldiacs). It has a bottom switch.
In 18650 mode they are 83mm tall. The bottom switch both works and locks with magnets. You only have to rotate the switch 7mm to lock or unlock. This action can be done with your little finger. This switch is only 7mm tall, with less than 3mm of this outside of the battery tube.
This mod will be released probably by the end of this week and is available on preorder at the present time.
This short length is with a full top cap, not a recessed top cap. We are trying to get them to offer a recessed top cap as an option in the future. This would make the mod in 18650 mode only 78mm tall as the full top cap adds 5mm.
Owners of Poldiacs can convert them to this new bottom button design by purchasing the switch and a Poldiac to Nanos adaptor ring.

I have a 18650 Nanos in polished brass on order and I am really looking forward to receiving it in the very near future. I ordered it on April 1st when they first offered them for sale.

 

[Blind Squirrel]

The Stingray from JD Tech is an incredibly short mod and works great! Here's a picture of mine in 18650 mode with a KFL+ on it, next to my Magneto (also in 18650 mode). Huge difference!

 

[Vietnam1]

the microstick and homoriko looks pretty tiny

 

[John_2x]

the microstick and homoriko looks pretty tiny

lulz.. sorry, I have nothing to contribute but immaturity

 

[HeiSINberg]

The Stingray from JD Tech is an incredibly short mod and works great! Here's a picture of mine in 18650 mode with a KFL+ on it, next to my Magneto (also in 18650 mode). Huge difference!
View attachment 330621

I actually do have a brass stingray and like its size. Thats normally my beater mod for on the go. My copper black stingray should be here sometime this week also. Thank you

Sent from my SCH-I545 using Tapatalk

 

[HeiSINberg]

I just pre ordered my XXIX from beyondvape and it should hopefully be here by may sometime. Thank you alkaiser for the measurements! I am too excited to get this mod.

Sent from my SCH-I545 using Tapatalk

 

[cracoucax]

The Stingray from JD Tech is an incredibly short mod and works great! Here's a picture of mine in 18650 mode with a KFL+ on it, next to my Magneto (also in 18650 mode). Huge difference!
View attachment 330621

Dunno about the stibgray but everything is small compared to a magneto. I's the tallest mech I have by far.


Sent from Tapatalk, typos its fault.