Smok Koopor Mini 60w

[AlaskaVaper]

Great tip! It does work, and solves a big problem for me: small type + old eyes = the need for a long time out on the screen.

I have not tried this trick yet but am grateful that there is a method that you say is working. I have been too busy fiddling with my Apollo that arrived yesterday and the Koopor has been languishing sadly. I certainly sympathize with the "old eyes"!

 

[TheotherSteveS]

That Boxer looks like a really fine device. I saw a review by Mike "hit that ...." Vapes and he had both the gray colored Lipo version and a white 133 dual 18650 version. The aesthetics of both were lovely and if price was not an impediment for me I would love to own either one.

I had it in my hands, fleetingly. It wasnt assembled correctly or it developed a fault in transit. I actually got a brand new, magnet-less version. It rocks!! Should get is back mid-week!

 

[BigEgo]

Can anyone do a resistance reading comparison on the same coil between the Koopor and another mod? Mine seems to read a bit higher than my IPVD2 on any coil I try.

 

[TheWestPole]

Can anyone do a resistance reading comparison on the same coil between the Koopor and another mod? Mine seems to read a bit higher than my IPVD2 on any coil I try.

iStick 100W: .52 ohm
Koopor Mini: .54 ohm

 

[BigEgo]

iStick 100W: .52 ohm
Koopor Mini: .54 ohm

My Kooper consistently reads .02 lower than my IPV-D2. Example: 0.173 vs. 0.192.

And yes that little difference makes a pretty substantial difference in vape temp (at least 20-30 degrees based on feel).

 

[KenD]

OK, my Koopor Mini crapped out on me tonight. All of a sudden it won't read resistances right and as a consequence (probably) tc doesn't work correctly. A titanium coil will glow bright enough to blind even at 400f. Also, at times it'll jump out of tc instantly (watts are auto-set to 2.1 at that point though, so that's great). No reason why it stopped working. Was fine this morning, left it home when I was out for a few hours, and when I came back it had this error. Did open a ticket with fasttech so I'll get a new one I'm sure, but this really bugs me as the Koopor was fast becoming my favourite mod :-/

Sent from my C6903 using Tapatalk

 

[BigEgo]

OK, my Koopor Mini crapped out on me tonight. All of a sudden it won't read resistances right and as a consequence (probably) tc doesn't work correctly. A titanium coil will glow bright enough to blind even at 400f. Also, at times it'll jump out of tc instantly (watts are auto-set to 2.1 at that point though, so that's great). No reason why it stopped working. Was fine this morning, left it home when I was out for a few hours, and when I came back it had this error. Did open a ticket with fasttech so I'll get a new one I'm sure, but this really bugs me as the Koopor was fast becoming my favourite mod :-/

Sent from my C6903 using Tapatalk

That sucks. I wonder if a DNA-40 chip would fit inside the enclosure. I really like the fit and finish of the mod.

 

[KenD]

That sucks. I wonder if a DNA-40 chip would fit inside the enclosure. I really like the fit and finish of the mod.

I really love the fit and finish as well, and everything else while it worked. Not at all interested in the dna40 chip anymore.

Sent from my C6903 using Tapatalk

 

[cheech226]

whoo hoo mine has cleared customs in chicago! shipping has been longer already than my cloupor mini - i had that in 10 days.

 

[Imperialchugger]

Waiting for koopor to arrive. should have them by this week.

 

[v1ks_]

Jumping in the bandwagon... Have a Koopor Mini w/ Goblin Mini on top as my first vape setup.
Working nice so far. No complaints... well, save for one, once you screw on the Goblin Mini on the, it's impossible to adjust it's airflow. Not a huge issue since it's wide open all the time anyway...

 

[Kmfm0122]

I really wanted better reviews on this device but SMOK is the name keeping me from buying it....

 

[v1ks_]

I really wanted better reviews on this device but SMOK is the name keeping me from buying it....

Better reviews?
Hrm, well, some Asian vendors have it priced as low as $30.99 at the moment. At that price point, I think it has gotten pretty stellar reviews. Hell, plenty of tanks cost more than that.
Also, at that price point, there are pretty much are no alternatives. Cheapest D2 I found is $40, Sigelei 75W is almost twice more than Koopor Mini and VTC Mini, afaik, has received more criticism than the Koopor Mini.

Then again, I started from a white page, without any prejudice against any manufacturer out there.

 

[Kmfm0122]

Better reviews?
Hrm, well, some Asian vendors have it priced as low as $30.99 at the moment. At that price point, I think it has gotten pretty stellar reviews. Hell, plenty of tanks cost more than that.
Also, at that price point, there are pretty much are no alternatives. Cheapest D2 I found is $40, Sigelei 75W is almost twice more than Koopor Mini and VTC Mini, afaik, has received more criticism than the Koopor Mini.

Then again, I started from a white page, without any prejudice against any manufacturer out there.

I have a handful of people tell me to avoid SMOK products but the TFV4 make me want one of their mods.

 

[VCross]

Their tanks are amazing and their old mechanicals were pretty good too but ever since they started doing regulated mods they haven't gotten any right until the Cube II. That being said I do love my M80 and as far as a VW mod goes it's pretty solid albeit buggy at times. I'll probably pass on this one but at $35 I'll probably get one just for the case and try to gut it lol

 

[BigEgo]

Still using my Koopor Mini alongside my IPV D2. Both are doing what they are supposed to be doing. I have no complaints from either.

 

[cheech226]

got mine today. however it looks like the verification stickers have been removed from the packing box. so i have no way to plug in the numbers into koopor's website. here's a pic of the box. is this where the code is supposed to be?

 

[KenD]

My RMA'd faulty Mini was received at Fasttech today. Unfortunately the Chinese national holiday will delay the shipping of my replacement :'(

On another note, have any of you plugged the Mini into the computer even though there aren't any updates yet? It's supposed to be recognized by Windows right? I got no reaction at all when connecting to the computer.

PS. Having said all this... While my Koopor worked it was great. I just happened to have bad luck and got one that crapped out on me.

Sent from my C6903 using Tapatalk

 

[v1ks_]

View attachment 494639 got mine today. however it looks like the verification stickers have been removed from the packing box. so i have no way to plug in the numbers into koopor's website. here's a pic of the box. is this where the code is supposed to be?

Yes, that's where the stickers should go.
I wouldn't worry too much about it though, especially if you ordered it from some Asian vendor. First of all, I can't imagine why anyone would bother cloning a ~$35 mod and secondly, Asian vendors tend to do that sometimes, or rather wholesalers do, who supply them to vendors. Usually it's because the vendor is selling them way below MSRP, and stickers are removed so the manufacturer has no way to track back the items to the wholeseller, who has sold the items to the vendor, cheaper than they've agreed upon.

Sorry if it makes no sense, heh... I recall being lectured by someone on the topic and I'm just re-telling stuff the best way I can.

 

[v1ks_]

My RMA'd faulty Mini was received at Fasttech today. Unfortunately the Chinese national holiday will delay the shipping of my replacement :'(

On another note, have any of you plugged the Mini into the computer even though there aren't any updates yet? It's supposed to be recognized by Windows right? I got no reaction at all when connecting to the computer.

PS. Having said all this... While my Koopor worked it was great. I just happened to have bad luck and got one that crapped out on me.

Sent from my C6903 using Tapatalk

I have not tried to plug mine in, but I wouldn't be surprised if Windows did nothing. The mod isn't smart enough to 'talk' to the computer. Some sort of software will be needed, to update the firmware(when/if they are released). The software will then check the ports, looking for the chip on the other end and then it will sort of "force feed" the mod, without actually asking it anything. It will simply push the files to the chip.