- Status
Bulli A2-TM 3ohms 4.0V. Still can't get The DID to work flawlessly (a lot of vapour, but no flavour, enough flavour but not enough vapour
)
Freddie is happy! Give him a break! Jeesh!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Now if we could make you stop abusing the !!!! button and darn,mimicking the GG fanbois by calling everybody brother (makes me nauseus)
Bulli A2-TM 3ohms 4.0V. Still can't get The DID to work flawlessly (a lot of vapour, but no flavour, enough flavour but not enough vapour
Don't give up on the DID. It will come. When you set it up perfectly, as I have now done, you will know it as the flavour and vapour will 'pop' and you will not be able to hold back a smile. Suggest a 5-wrap 2.2-2.4ohm coil for the vmax at 3.4-3.8v.
Hint: After setup, if you're unable to take the wick out of the coil fairly easily and without it binding anywhere, and replace it just as easily, both without disturbing the positioning of the coils, you likely don't have it set up right.
Well FINALLY !!!!!!!! My DiD has FLAVOR !!!!! Thick Thick Vapor , Perfect TH, And a very nice draw to it. I do think I'm going to find a piece of PTFE tubing to fit the wick hole snug and maybe make a disk to cover the bottom plate of the tank to cut down and completely eliminate any way of shorts from happening in those 2 areas. So as of now it's working awesome with 4 coils @ 2.4Ω on the VMAX's @ 3.6V and the NEW Chrome 4 amp LT V2 @ 3.9V..... and I have to say this new LT is really really nice, Im blown away by the quality and the power this unit makes, highly impressed, I was expecting garbage. Anyway the "DiD" is "Doing" GREAT on the VMAX's !!!!!!! Take care ALL ,.....J
Oh Yeah........
Oh Yeah........
HAPPY 4TH EVERYONE.....
BE SAFE OUT THERE !!!!!
BE SAFE OUT THERE !!!!!
Last edited:
Yaaaaaay J!
See? Resistance is NOT futile
Enjoy and Happy 4th of July to all our American friends.
See? Resistance is NOT futile
Enjoy and Happy 4th of July to all our American friends.
Yaaaaaay J!
See? Resistance is NOT futile
Enjoy and Happy 4th of July to all our American friends.
And don't forget last but certainly from from least ALL of our active duty, reserves, and ESPECIALLY OUR VIETNAM VETERANS !!!
Heres wishing a happy 4TH to ALL of our Military Personnel....Ladies and Gents !!!
Kir Fanis Tripolitis and Trap tanks.
The pics don't even begin to describe the craftsmanship of these art pieces. Absolutely first class machining and construction. You really have to hold one in your hand to understand.
The clear tanks have frosted top/bottom lips and an interior ledge upon which the o-rings sit securely. The design also includes top nuts for easy filling and less wear and tear on the o-rings. Just brilliant.
Clear tanks also more resistant to aggressive juices than typical polycarbonate.
I'd say today's vape mail was pretty nice.
Very nice Fuzzi, I love my pyrex tube on the DiD. Tastes soooooo clean and robust.
Its always nice when you guys post your setups (ohms,this and that) but you always leave out the gauge of the wire (and type)
For example,my woes are made with 32 kanthal A1 (still cant get a coil to last more than 0.01 sec on the vmax)
For example,my woes are made with 32 kanthal A1 (still cant get a coil to last more than 0.01 sec on the vmax)
So I get a I4 charger in the mail yesterday! I throw 4 brand new efest batteries on it and wait. A short time later they are done. With out thinking I grab them off the charger then start testing voltage on them. 4.08, 4.21, 4.20 and 4.19. WHATS up with the 4.08? I wish I would have payed attention to which slot it came out of. So I throw them all back on the charger and the 4.21 is done right a way. the 4.2 and 4.19 are done a short time later, but the 4.08 takes a while. So before I go to bed I see they are all done and I just unplug the charger. This morning I test them all. 4.19 and 4.18s. (I figure after setting all night a little drop is normal). Is 4.08 in the acceptable range for being fully charged? Just shows to check your batteries after they are done!
I'm using the same wire. You have shorts. Also see my hint in post 1362.
Do, or do not. There is no try
Another thing Martin. For the longest time I couldn't figure out where it was shorting so I took out the wick and inspected it closely. Turns out an almost invisible strand was protruding out the bottom and making contact with the side of the tank. Pulled it out and smooth sailing.
Can you spin the wick within the coil with an absolutely minimal amount of friction?
Always,the coil I have removed from that one rubbed a tiny bit against the mesh but came out whole
Quick question for those using the DCT and 801 fusions.... Is the dct 3.5ml tank with stainless steel end caps ok to use with those or does it have to be the 6ml dct?
If you have the Smoktech 3.5 slim DCT, then the Boge 801 XL Fusions will work for both!
- Status
Similar threads
