- Status
Yep 2 wires up to the connectors, I used heatshrink on the connector ends themselves once the wires were soldered to them and placed them into the predrilled holes. Here is a variaton of another quick connect/disconnect I want to try:
Dan
I like your idea Dan,
Those are going to be some small springs though.
I think that I'd put an isulating washer under the spring that's a little larger though. I know you've got the nylon insulator under there but springs like to wiggle around enough under compression (unless you are really close on the spring ID fit) that it probably warrants it.
Those are going to be some small springs though.
I think that I'd put an isulating washer under the spring that's a little larger though. I know you've got the nylon insulator under there but springs like to wiggle around enough under compression (unless you are really close on the spring ID fit) that it probably warrants it.
Ok guys.
I'm having a heck of a time rolling 400 mesh in Dans design.
I can't get it to bend, it always folds.
If I roll it tighter it freys.
I've got 325 to work out. But there's something I'm not liking about 325.
Any suggestions?
Thanks.
Sent from my HTC Glacier using Tapatalk
I'm having a heck of a time rolling 400 mesh in Dans design.
I can't get it to bend, it always folds.
If I roll it tighter it freys.
I've got 325 to work out. But there's something I'm not liking about 325.
Any suggestions?
Thanks.
Sent from my HTC Glacier using Tapatalk
The way I get it to bend so nice is to roll it while bending, never had it fold when I did that. I usually start dead center and pull while rolling a couple time and then roll while bending. Works for me
Dan
Dan that sounds kinda hard. Do you roll it a little then bend it a little then roll a bit more?
I made a mod like yours with a Ce2 but I think it doesn't wick properly because there is no ferrule tube. I don't know I'll post it some other time. Right now all my e-cig mod effort is going into my genesis build.
I made a mod like yours with a Ce2 but I think it doesn't wick properly because there is no ferrule tube. I don't know I'll post it some other time. Right now all my e-cig mod effort is going into my genesis build.
Nope, one continuos motion. Guess I might have to do a video
Dan
......
Hey obeer, I had the same problem at first. The trick it to use a smaller soldering tip on a cooler iron. I melted a couple of them with my soldering gun then tried a 25w iron with a precision soldering tip... No more melted switches
Hey obeer, I had the same problem at first. The trick it to use a smaller soldering tip on a cooler iron. I melted a couple of them with my soldering gun then tried a 25w iron with a precision soldering tip... No more melted switches
Haha. Looks like we both learned the hard way. All I've got is a 30 Watt and a butane, both without fancy tips. Guess I'll have to shop for more tools....oh darn.
Even a good iron won't help their poor quality. I was running 50% DOA right out of the package.
I found (and have posted it somewhere in this forum) the 10 amp switches that I will use from now on.
I'll add a link here when I find them.
I found (and have posted it somewhere in this forum) the 10 amp switches that I will use from now on.
I'll add a link here when I find them.
Hmm...and I was thinking these were robust. I've soldered mine twice so far..
I found the link. They only need a 12mm hole and have a nice tac type feel. The 10 amp rating is for 110 AC, I have no idea what the 6v DC rating would be. Perhaps one of our resident EEs could answer that question.
1pc Waterproof Momentary OFF-(ON) N/O BOAT Switch,BK33B | eBay
1pc Waterproof Momentary OFF-(ON) N/O BOAT Switch,BK33B | eBay
I .soldered one of mine 3 times. I only had to solder the one on the mini once.After a couple of months they are still working fine.
Woohoo, my Stewalin showed up today, snailmail Germany to Tampa took forever
Would you mind sharing your source? And the amount ordered along with total price including shipping? Thanks!
Here is some good ceramic stuff for those in the US...I have some and it is good stuff. As shown in the pic below I have used it to coat a coil wrapped around a glass tube and it gets red hot and doesnt chip off. Good for molding your own cups too. To fully cure it just hit it with a torch until red hot. I talked to the company and it is non-toxic when cured.
AUTOCRETE,1LB JAR - Flexbar
AUTOCRETE,1LB JAR - Flexbar
Last edited:
Ha...I'm still working on everything...but nothing ever gets done! No..I have been using a glass tube mod for quite a while now...I will get some pics or a vid up here some day soon.
What have you been up to lately?
- Status
Similar threads
