update got some new orings no more leaks but the problem now is the 510 connector is to short so the 510 pin even screwed out a tone just gets pushed up into the 510 connector on all my mods.
Squape Reloaded Clone
- Thread starter yungstu
- Start date
- th_trl_thread_readers 0
- Status
Ok, SqR from fc is here. I disassembled for cleaning, and see my plastic tank has no o rings holding it in there at all. The white ones in the spares bag I assume are the ones I need? I think I can tell where they go, but I'm not completely certain. As it is on arrival, I can just pull the plastic tank right out so I know there are none in it.
The rest appears nice so far.
The rest appears nice so far.
Sorry to hear about all the problems with leaking tanks and bad 510 pins. I thought the Chinese clonemakers finally got their act together. But it seems they have no understanding of Quality Control.
I think the top o ring is in, but I have no clue on the bottom one 
they are very loose, and I just can't get it.
they are very loose, and I just can't get it.
Yes I received mine the same way ... That lower oring is difficult... Most orings u gotta stretch it into the groove but this one just go around slowly pressing it into the groove
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Yep putting the o-rings in the tank can be a pain in the ....
Gvapers contacted me and they are getting replacement parts and will send me when they arrive at Gvapers. (i need a complete new base).
I must say that James from Gvapers react fast on my mail about my issues with the Squape.
My squape arrived in a bad condition but the service from Gvapers is excellent.
Gvapers contacted me and they are getting replacement parts and will send me when they arrive at Gvapers. (i need a complete new base).
I must say that James from Gvapers react fast on my mail about my issues with the Squape.
My squape arrived in a bad condition but the service from Gvapers is excellent.
Ok, got it finally. What a pain in the ...! I can see why they're sending them out without the o rings in; they don't want to do it either!
I don't care how good this thing vapes, I'm not buying another
I don't care how good this thing vapes, I'm not buying another
Ok, got it finally. What a pain in the ...! I can see why they're sending them out without the o rings in; they don't want to do it either!
I don't care how good this thing vapes, I'm not buying another
Out of all my tank atomizers, the squape rates second to the bottom.. In flavor and in vapor
Sent from my iPhone using Tapatalk
Last edited:
New problem: I've coiled it 3 times now and it keeps reading 0.1-0.2 ohms. 8/7 wrap with 28 gauge on 3/32" bit using kanthal.
Any ideas?
Any ideas?
Make sure your 510 pin is out far enough on the squape, I had to unscrew mine a little bit, to make good connection with my hana
I did. This is on my ohm meter. Bringing it out farther didn't change anything.
Roxy, I've head that you need to check the 510, the screws and pins for emetal overspray and make sure you clean everything off.
I didn't bother, mine were sent back and I got a refund.
I didn't bother, mine were sent back and I got a refund.
Also raising the coil a bit off the deck helps too
Sent from my iPhone using Tapatalk
I still have them but I didn't try. The ehpro deck doesn't come out easily at all. I actually scrapped my finger trying to remove it. It was dry when I tried and it might be easier with eliquid. But I finally got a great build in it with xc116 and I don't want to mess it up to try lol it took forever to get right.
I was told by scraping it or repeatedly tightening and loosening the 510 screw.
My eye's aren't good and that is why I sent them back.
My eye's aren't good and that is why I sent them back.
I sanded the post screws and the 510 screw. Its working now. My wicking needs work though because I'm getting some dry hits. I used Busardo's build on the wide deck, but I'm going to go watch some other vids.
- Status
Similar threads
