Stainless Steel capable mods

[sofarsogood]

Might be that they're sitting on ten thousand kanthal heads...

I bet there is more to it. I like recommending the nautilus mini because I know it well. My brother has one. I steered him into a backup mod finally and it has temp control. If he could get stainless coil heads for the N mini he could go both ways.

 

[jaysterl]

Here are two more that claim to have Stainless Steel TC both are attractively priced at less than $50 .

pioneer4you IPV5 200W TC Box Mod features the Yihi SX340 chip

KANGER KBOX 120 WATT / TC BOX MOD

 

[Susaz]

Thanks everyone, it's given me quite a lot of ideas
I'm falling in love with SS, soon it'll be the only thing I vape on. The Cubis and the GG Tilemahos with springomizer changed the way I see SS. To me it's a great thing to vape on!

 

[Poeb09]

Was the rx-200 SS function for 316l or 304 i had issues running 316 on the preset SS tcr but no issues on my dna.

 

[Highwayman1224]

I purchased some UD 316L SS wire in 26ga & made a . 56 2.5mm coil and it's working fine on my rx200. Running it at 520 degrees at 40 watts. First time I've ever used stainless steel.

Was the rx-200 SS function for 316l or 304 i had issues running 316 on the preset SS tcr but no issues on my dna.

 

[KenD]

Was the rx-200 SS function for 316l or 304 i had issues running 316 on the preset SS tcr but no issues on my dna.

With the 3.0 firmware it's supposed to be for ss316.

Sent from my M7_PLUS using Tapatalk

 

[Jim_ MDP]

I haven't seen squat about SS TC performance on the new Kangers.
Which actually means it's probably working at least passably well.
Unlike this first pass at NiChrome TC.
TCR of 0011?. Not gonna happen Skippy... let it go.

But I don't like their looks. I just don't.
And being a stubborn .......... I'll probably pick up the new i100TC at some point.
And be wishing they had made it a 120w.

For better or worse, it's an Eleaf, which is JoyeTech, so the SS should closely match theirs and the Wismecs, also a JTech subsidiary (my VTC and RX are good on 316L and just fine with TCR Adjust).

The new trio from Vape Forward (that's Vapor Flask's actual company name) are coming from a partnership with Wismec (there's JTech again. Damn... vape world domination anyone?).

I was never familiar with the VaporFlasks and their TC performance. Well liked though.
Were they great? Will the new mods use existing VF code... or Wismecs?

So there's eight or nine SS TC mods in one post.
Suckahs!

*drops mic*

 

[Susaz]

Does anyone have a Presa 75 TC?

 

[Jim_ MDP]

There's a thread for it, I believe.
Quite a few VTC owners picked one up. Especially after JTech/Wismec put the Presa's version of the 3.0 update on it. Similar screen layout and TCR Adjust.

Plenty of happy campers from the reviews I've seen.

 

[BigEgo]

I was never familiar with the VaporFlasks and their TC performance. Well liked though.
Were they great? Will the new mods use existing VF code... or Wismecs?

Vaporflask used to be a high-end device. $300 or there abouts (which was inflated no doubt because it was made in USA). They used DNA-40 and SX350J boards exclusively.

Their partnership with Wismec was supposed to bring the cost down significantly, which it did. Now they use Joyetech boards inside, which also helped bring the cost down.

 

[Jim_ MDP]

They must be hitting the shelves by now right?
I guess I'm just waiting to hear if VapeForward had more contribution than "make it curved".

 

[cobalt327]

VF has released three recently- Lite, Stout and Classic. There's a thread on the VF "Stout" (possibly on the others as well). 26650 battery for the Stout.

 

[Susaz]

They must be hitting the shelves by now right?
I guess I'm just waiting to hear if VapeForward had more contribution than "make it curved".

Bought a Stout, works great, and now come think of it, the lineup is all Joyetech boards!
Vaporshark DNA200
RX200
Joyetech Cuboid
Vape Forward Stout
Evic VTC Mini
and I'm planning on getting the Presa. Except for one, all wonderful Joyetech boards!