Svoë Mesto Kayfun III ES Discussion/Questions

Status
Not open for further replies.

hant

Full Member
Verified Member
Mar 6, 2013
54
28
Russia, Ekaterinburg
If you said you are fed71 then most likely you are banned again.
Good luck buddy and thanks a lot for what you have done here.

I do not fed71
I hant, friend, neighbor fed71.
I do not use CM, I do not like it.
I send your message from fed71 for you.
Me banned?
I wanted to spit on them: D
Я хант, мне пох й (HMAO Russia): D
 
Last edited:

Idaholandho

Gone Fishin'
ECF Veteran
Verified Member
Dec 8, 2012
7,379
23,171
Reading Naked
For the record, there is a kayfun lite thread.

I'd be interested to see prices and postings in 'The Russian' thread, but it managed to close itself for coop-hiding.

Im glad there is a kayfun Lite thread and am aware as many of us are....Oh did you see my Lite on a PAPS?
RbNpBrB.jpg


If you are interested in the Chinese copy(theft imo) of yet another device than you must know there is more than one thread and good luck.

Always wishing the best to all in their days,
 
Last edited:

eratikmind

Vaping Master
ECF Veteran
Verified Member
Mar 22, 2013
5,481
4,712
Las Vegas/San Francisco
Does anyone run cotton yarn as wicks in their Kayfuns? I quit using silica about a month ago in my drippers and I used some to setup my new lite. I can taste the silica pretty hard now, icky stuff.

I have had a roll of cotton yarn and a box of CVS rolled cotton sitting in my parts bin for over a month. Since I slowly switched over to silica base designed devices, I have been using pre-torched german silica and ekowool in all of my devices.

Perhaps, at some point, I will give the cotton yarn and rolled cotton a try.

- Andy
 

Idaholandho

Gone Fishin'
ECF Veteran
Verified Member
Dec 8, 2012
7,379
23,171
Reading Naked
I like Ekowool. How often do you change the wick?

As little as possible. Im at 1.2ish ohms and in the small evac chamber the wick and coil seem to get darker a bit faster. Every 3 days or so I disassemble down to the chamber, take it off and rinse the wick out with hot water. I also have a small soft brush I lightly run accross the coil and rinse. This is one set up I dont torch clean(no reason). I then dry wick with paper towel and of course check coils.
This to me will maintain the wick longer in turn allowing the wick to last longer.
I rinse all my attys with ekowool out.
I will hit the wicks with a torch before juice soak.
Anyway, my wicks last 3+ weeks
 

Idaholandho

Gone Fishin'
ECF Veteran
Verified Member
Dec 8, 2012
7,379
23,171
Reading Naked
Def stick with pure Russian ekowool. I know steam monkey does sell the real deal. Most of the good stuff is in Poland and Russia but, watch for vendors that claim fibres based on pure Russian ekowool. *cough^.
The Steam Monkey crew knows much about media and have written several articles on "safe wicking" issues.


Here is the good stuff

Silica wick for Clearmizers, mods and atomizers - HangsenShop.eu
GL
 

classwife

Admin
Admin
Supporting Member
ECF Veteran
Verified Member
May 9, 2010
98,570
161,096
68
Wesley Chapel, Florida
makes one think some of the rule nazis are a lil bit ......ed or power hungry, posts should be evaluated for what they are and not just deleted cuz it belonged to one single person? just my 2cents

You need to take a minute and go read the Forum Rules.


I do not fed71
I hant, friend, neighbor fed71.
I do not use CM, I do not like it.
I send your message from fed71 for you.
Me banned?
I wanted to spit on them: D
Я хант, мне пох й (HMAO Russia): D



Both of you...It would be my pleasure to close your accounts if you don't want to be here.
 

Idaholandho

Gone Fishin'
ECF Veteran
Verified Member
Dec 8, 2012
7,379
23,171
Reading Naked
A quick question, I've been trying to get a kayfun and wondering, how is the draw? Any way to control it? I like really airy draws on my atties..

There is an air control. Most do prefer the airy draw. If anything, I feel the air control would only help if I was having wicking issues and needed to compensate for a substandard wick setup, ie - a bit too much wick stuffed in the evacuation chamber.
GL
 
Status
Not open for further replies.

Users who are viewing this thread