Svoë Mesto Kayfun III ES Discussion/Questions

[Blix]

Not seen any bubbles in mine.

 

[sahilm]

Thank you Blix sir .

atm trying to run mine with a 2 ohm coil , 50/50 juice , provari at 4 volts . if i cover the air hole and suck juice into the chamber i get a good 4- draws , after that ... dry again , Nose burning dry .. Jeeeeez , frustration at 100%

best wishes
Sah

 

[sahilm]

Dear Fed sir , thank you again and i am extremely sorry to bother ALL of you here with my problem .
I can see how everyone is coming together to try and help me out , another ++ of the vaping family .

Sir , i have many times tried the following :
when i make my coil and put the chamber on , before i put the cap of the chamber on i put 2-3 drops of eliquid on either side and wait till i can see it coming out of the 2 slots on the side to be sure that the inlets of the chamber are free ...
I only put the outer tank and top on after i have confirmed this .

warm regards
Sah

 

[sahilm]

Dear all i got to say :

The Kayfun 2.1 is what i am going back to again and again , and the 2.1 vapes like a champ ... i wish the 3.1 was half as good as the 2.1 ...

Do i need to dremil the slots a litttttle more !!!!

warm regards
Sah

 

[sahilm]

Dear Fed Sir, Thank you so very much once again.
i have read through the post above and will also go through each thing CAREFULLY again tmrw .

i just saw another setup which i will very carefully and step by step setup tomorrow ( Kayfun 3.1 ES - setup re-wick - re-coil -- My Method | ALL ABOUT E-CIGARETTES UK ) .

I really appreciate all the help I am getting and will certainly report back at the earliest .
Best wishes and warm regards
Sah

Btw , i just opened the air intake of the kayfun 2.1 to full and Oh Dear God .... its a vape monster , So glad i got this too .

 

[overall]

I have had a short term experience like this with my first setup. Every few puffs I would suck on the drip tip while covering the hole. Seems to have sorted itself out now. I opened mine up last night to check the wick and coil. All was good and juicy in there. So I filled her up and went on my way.

Dear all , a very good day to everyone and i hope all of you are in good health and are enjoying your respective kayfuns - .

I have been now vaping for nearly 3 years ( in June ) , and have been through it a LOT of diff devices starting from 510 attys and tea bags and blue foam - Lol.

i recently got the kayfun from cloud 9 vaping and set it up as per todds review , it vaped pretty fine but i got a few dry hits , thinking i was new to it and needed to adjust something i kept trying to get a nice vape out of it , sometimes it would work ok and sometimes dry hits , its been over a month now and i have tried every darn method under the sun to try and get rid of the dry hits .

I have tried diff silicas , ekowool , diff thickness , diff kanthal , nicrome , ribbin wire , You name it and ive done it , ive tried the navy seal method , been through pretty much all the videos on youtube and have even tried the method my friend Mark puno shows .

BUT i am still getting dry hits after a few vapes , what could be the problem !!
I would also like to mention at this point that i have a kayfun 2.1 also and that works perfectly fine , no dry hits and awesome vapour .
I have noticed one thing tho , when i vape on the 2.1 i can see little air bubbles coming up , BUT i have never noticed this happen on the 3.1 . could this be a problem , could any of you kind people check here if you get air bubbles from the 3.1 ...

would HIGHLY appreciate any and all input .

thanking you once again .
best wishes and warm regards
Sah

 

[artline007]

im interested in promocodes!

care to share?

How we have a Discount Coupon Code for Kayfun ands its accessories

 

[montara]

Gamma on sale right now
Svo

 

[btally]

Gamma on sale right now
Svo

That didn't last long, it seems to be out of stock already. Wasn't the Gamma discontinued? Or at least they had it on hold while they were working on getting the finish to be more uniform?

 

[badinfluence357]

I've seen the bubbles, while vaping you see a lil bubble slowly moving up....lol I love it!!!


Sent from my SCH-R910 using Tapatalk 2

 

[CoyoteRed]

I've seen the bubbles, while vaping you see a lil bubble slowly moving up....lol I love it!!!
View attachment 210017

Sent from my SCH-R910 using Tapatalk 2

Seeing the bubbles is like "seeing the light'' it means your are entering vaping heaven.

 

[hippieben]

I don't remember if I asked in here or thought about asking, and if I did ask I don't remember if I got an answer. Anyway, will we be seeing parts any time soon? Specifically metal tanks and expansion funnels?

EDIT: I see that the expansion funnel is listed on the SM store, now I just want more metal tank parts

 

[sahilm]

Dear All a very good day again and i hope everyone is well .

Spent pretty much of the day tinkering with diff setups for the 3.1 , finally after about 6 diff tries i think i may have found the answer to my problem .

Just one 3 mm silica wick in a " S " shape . nicrome wire / 5 wraps , 1.8 ohms and vaping nice .

Have not had any dry hits at all yet ( 2 hours ) , made sure that the silica was on the base BUT away from the juice inlets on both sides of the chamber and i could see the inlets clearly .

I will report back again tmrw , as of now it all seems to be in order .

thanking you all once again for all your help .

best wishes and warm regards
Sah

 

[Blix]

Great to hear Sahlim, hopefully you got it rockin' now!

 

[sahilm]

Dear Blix Sir a very good day to you .
yes sir it is vaping pretty nice , it seems that less is more here . less silica = better feeding and soaking of the wick for a no dry burn vape .

shall keep all you kind and helpful vapers updated as i go along . So long its good

thanking you once again
best wishes
Sah

 

[martinc]

Awesome

 

[CoyoteRed]

Yes. Measures have been taken to improve the quality of the coating Gamma. This was announced by Sergei aka svoemesto.

And I think there is a need to explain some of the issues. Information from svoemesto:

We draw your attention to the fact that at the moment there are still serious problems with the timing of deliveries of parcels - large and unpredictable delays on both the Russian Post, and on the side of customs. Delivery time may be increased up to 8 weeks. Unfortunately we can not influence it, we apologize for the inconvenience.

We are often asked to send a parcel from Russia some express shipping - EMS, DHL, Fedex, etc. The cost of such a parcel from Russia - about $ 150. We tried to do it and the result did not satisfy us. By express-parcels from customs attention, and for each such parcel has to be carried a long correspondence with Customs - what is this product for what it is, how much it costs, if it is allowed to export, etc. etc. The result is a long, expensive and thus a lot of problems. Charging customers extra large sum of money for this "express" delivery, we can not afford.

We often write that e-mail notices about the availability of goods in the store, whereas when entering the store the goods anymore. According to the rules of our store after ordering items in stock is reserved for 3 days. If the 3 days the order has not been paid - it will be canceled and the goods of this order is returned to the store. If the product is already in the store did not have - that triggers the mechanism of "notification of the availability of goods." The first stopped by the store customer orders and product again no.
All the major revenue items in the store are always accompanied by a newsletter, while delivery date of the canceled orders in the automatic mode. If you want to always be aware of the availability of the goods in our shop - subscribe to the newsletter store, and not only on notice of the availability of goods.

I ordered last batch and it took about 20 - 23 days. Are you saying that this time it is going to take over 60 days?
I know you have shipping problems but if that is the case,in my opinion that kinda puts you in the not feasible to do business with.
I love the Kayfun but not to the point of waiting months to get it after putting money up front.
There are other quality devices out there that you dont have to wait this long for.
I can deal with 20/30 days,Please tell me you do not expect me to wait 60 days.

 

[tim_man]

I don't think it means a 60 day wait - he's just cautioning us that it can take up to that long due to the unpredictability of Russian post and customs...

 

[nilbog]

hehe! semovar update vapn?

 

[hippieben]

Over a month later, here's the kayfun video

Kayfun 3.1es English Review / Tips & Tricks - YouTube