Taifun GT Discusion!

[dems86]

what build you rocking in there dems??

26g, 2.5mm, about .8ish ohms...although I have some 26/32 Thunderhead Clapton wire on the way and I'm looking forward to trying out some of that


Sent from my iPhone using Tapatalk

 

[TheotherSteveS]

26g, 2.5mm, about .8ish ohms...although I have some 26/32 Thunderhead Clapton wire on the way and I'm looking forward to trying out some of that


Sent from my iPhone using Tapatalk

Cheers lad. I think that might be the limit for the Eye to be honest. 26 was just what I had in mind actually. Great minds think alike, and so do ours apparently...

 

[h00ligan]

Cheers lad. I think that might be the limit for the Eye to be honest. 26 was just what I had in mind actually. Great minds think alike, and so do ours apparently...

How do you clean typically? I use warm water / washing up liquid / rinse / sonic. The washing up liquid is necessary for grease cutting but he scent they add can be tough.

 

[52anddone]

The Hotcig GT-S is the one I would recommend, aside from the deck being removable it is 1:1.
$20.02 HOTCIG GT-S V2 RTA Rebuildable Tank Atomizer (5.0mL) - stainless steel + matte glass / 23mm diameter at FastTech - Worldwide Free Shipping

I am waiting on FT to ship mine, in the mean time though, what (if any) spares do you recommend that I get for this one ??

 

[we87]

Question for those who have been using the new air- can you compare the amount of airflow to the gs2?

I'm just curious if it's an insane amount of airflow now. From what I can tell from the video posted earlier it sure looks like it. The guy looks like he is vaping from a dripper not an rta granted its dual coil in his video but still, looks like a big big airflow improvement.




Sent from my iPhone using Tapatalk

 

[dwcraig1]

I am waiting on FT to ship mine, in the mean time though, what (if any) spares do you recommend that I get for this one ??

I can't think of anything needed, it comes with spares.

 

[52anddone]

I can't think of anything needed, it comes with spares.

I ment like those little tubes that you put in the air tube to reduce the airflow CFM under the coil, and extra o-rings to keep on hand (extra Extra's) or extra glass (I have 5 extra glass tubes for my Lemo V1), extra screws, things like that.

 

[dwcraig1]

I ment like those little tubes that you put in the air tube to reduce the airflow CFM under the coil, and extra o-rings to keep on hand (extra Extra's) or extra glass (I have 5 extra glass tubes for my Lemo V1), extra screws, things like that.

It comes with an extra glass and o-rings

 

[52anddone]

Thanks dw.

 

[dwcraig1]

Thanks dw.

It appears I missed adding just a bit of info on this air reducer. The plastic tube supplied will reduce it to 2 mm, a 1.5 mm metal draw tube (TGT1) can be inserted into the plastic tube. I suspect it to be just fine at 2 mm though. The genuine service set (should) have the 1.5 mm draw tube as well as two 3 x 2 mm plastic tubes.

 

[dwcraig1]

So I got back to messing with one of my TGS2-22's, what a confused soul I became. 1st. I couldn't figure out what TC coil was in it currently so I made another one with NiFe52. I then decided to just use the one in it and put the new coil away. Next day I decided to put in the new coil but It wasn't doing any TC, that's when I discovered I wound it with NiFe70 instead of NiFe52. But that wasn't the end of it, when I grabbed the new coil I grabbed the wrong one, it was a Kanthal that I had made some time earlier and didn't use so that was the reason for no TC. DUH...DUH...DUH......
It does work great though, this one is my first attempt at using short mesh tube sitting on the wicks shoulders. (other than FEV style coil setup)

 

[chanelvaps]

So I got back to messing with one of my TGS2-22's, what a confused soul I became. 1st. I couldn't figure out what TC coil was in it currently so I made another one with NiFe52. I then decided to just use the one in it and put the new coil away. Next day I decided to put in the new coil but It wasn't doing any TC, that's when I discovered I wound it with NiFe70 instead of NiFe52. But that wasn't the end of it, when I grabbed the new coil I grabbed the wrong one, it was a Kanthal that I had made some time earlier and didn't use so that was the reason for no TC. DUH...DUH...DUH......
It does work great though, this one is my first attempt at using short mesh tube sitting on the wicks shoulders. (other than FEV style coil setup)

had to LOL here

 

[Phone Guy]

I saw ft now has the kayfun mini v3... I wonder when they'll get the taifun air?

 

[52anddone]

It appears I missed adding just a bit of info on this air reducer. The plastic tube supplied will reduce it to 2 mm, a 1.5 mm metal draw tube (TGT1) can be inserted into the plastic tube. I suspect it to be just fine at 2 mm though. The genuine service set (should) have the 1.5 mm draw tube as well as two 3 x 2 mm plastic tubes.

That's what I was wondering (and hoping) about dw. I guess that I'm a little bit different from most vapers, as I like a tight draw, on my Magma I had the airflow ring set to 2mm most of the time (I mean set for 2mm in single coil/single airflow hole configuration running a 2.5mm coil). My Toot has shipped from FT, but my TGT-S V2 and Hurricane haven't yet. Thanks for adding that info for me as I haven't gotten to the TGT-S V2 section of this thread yet, I'm on page 115 reading what Bill had posted about wicking (very interesting).

 

[dwcraig1]

I saw ft now has the kayfun mini v3... I wonder when they'll get the taifun air?

I'd guess within two weeks.

 

[h00ligan]

It appears I missed adding just a bit of info on this air reducer. The plastic tube supplied will reduce it to 2 mm, a 1.5 mm metal draw tube (TGT1) can be inserted into the plastic tube. I suspect it to be just fine at 2 mm though. The genuine service set (should) have the 1.5 mm draw tube as well as two 3 x 2 mm plastic tubes.

So far it seems now after a week I'm going to have to call for mine. In surprised vapinart haven't answered me. Phone call it is

Such a pain for such a basic small tiny little thing. I can't believe we collectively haven't figured out what this stuff is and where to get s spool
If it or at least soares that don't cost $20

 

[dwcraig1]

So far it seems now after a week I'm going to have to call for mine. In surprised vapinart haven't answered me. Phone call it is

Such a pain for such a basic small tiny little thing. I can't believe we collectively haven't figured out what this stuff is and where to get s spool
If it or at least soares that don't cost $20

Maybe here:
PTFE Teflon Tubing Pipe ID2mm OD3mm For 3D Printer 1.75mm Filament

 

[h00ligan]

Maybe here:
PTFE Teflon Tubing Pipe ID2mm OD3mm For 3D Printer 1.75mm Filament

That's a great idea. I bought a meter from
Amazon for $4 shipped. No waiting for China ship

Fluorotherm F018N/A6 - 1 Metric FEP Tubing, 2 mm ID x 3 mm OD, 1' Length, Transparent Fluorotherm F018N/A6 - 1 Metric FEP Tubing, 2 mm ID x 3 mm OD, 1' Length, Transparent: Amazon.com: Industrial & Scientific

 

[h00ligan]

So if anyone can just measure the length of the air reducer pieces just to save some trial and error time - I'd appreciate it.

Thanks @dwcraig1. Nice job figuring what it is

 

[dwcraig1]

So if anyone can just measure the length of the air reducer pieces just to save some trial and error time - I'd appreciate it.

Thanks @dwcraig1. Nice job figuring what it is

4 to 5 mm should do, the TGT 1 draw tubes are 10 mm long.