- Status
My 2 cents, make the coil on around a 1.6 mm shaft. the wick that fits the coil should then be the right size for the holes in the chamber.
The restriction is probably where the cotton passes through the holes on the chamber, perhaps thin them down on the ends.
agreed
honestly, my build looks like a bit too much cotton as well, but that's the same wick for 1.5 days now and it's been good
honestly, my build looks like a bit too much cotton as well, but that's the same wick for 1.5 days now and it's been good
I use micros and cotton only in my drippers except for Aqua and Fogger, all others are traditional wrap on doubled over 3 mm silica.
I get months from them with maybe a weekly dry burn.
Oh I forgot one, micro and cotton is in my Mister Silica (might be my favorite atty)
I get months from them with maybe a weekly dry burn.
Oh I forgot one, micro and cotton is in my Mister Silica (might be my favorite atty)
Last edited:
I tend to stick with the same tank until empty. Before my brother broke my other taifun, I would have 2 hana with a taifun each with separate flavors, but that's kinda gone
/RIP
I think I'm going to make him buy be a fogger v4 as reparations
/RIP
I think I'm going to make him buy be a fogger v4 as reparations
Here's a coil I've been using for about a month, I think. Gets a good rinse and dry burn between every tank. It's about .8 Ohm. I think that's a 2.4mm diameter. 28 gauge. 4 wraps. It will be replaced soon....ish.
Ughh just got my replacement ss tank after they sent me a drip tip on accident before.
the package is charred and looks like its been run over by a 18 wheeler transporting shamoo himself.
Thing is oval and not usable lol i hate usps
the package is charred and looks like its been run over by a 18 wheeler transporting shamoo himself.
Thing is oval and not usable lol i hate usps
1.6mm coil? That seems a little small for me. I usually use 2.0mm (according to the precision screw driver kit anyway), and I end up around 1.3ohm generally, works fine. I'll recoil and post some pictures later on.
Actually 1.6 is just a bit large... http://www.e-cigarette-forum.com/fo...ils-increase-vapor-flavor-th.html#post9497477
Some may find this chart useful,
http://www.e-cigarette-forum.com/fo...por-flavor-th-microcoils-resistance-chart.pdf
Last edited:
Do you guys draw on the Taifun as how you would on a dripper? Coming from REOs and dripping, I forgot how I should actually draw on a bottom fed tank system. Slowing my draw seems to eliminate the cotton taste. Though vapor production drops. Maybe I'll rebuild my coil back to 0.9 ohm.
I took out the air tube and plastic bushing from the coil deck in my GT.. I feel it improved airflow and draw, but now I'm getting like sloshing sounds? I've even taken it back out and added a tiny bit more cotton to the collapsable collar holes thinking I was getting a little flooding, but I'm still getting that sound. Sounds like when your drinking the last bit of soda from a togo cup through a straw.
No flooding per se, but obviously something is going on.... I guess the airtube was preventing that sound. I've tried blowing thru the air hole from the outside, I don't hear any fluid being pushed or anything.
I'm a little lost here. I was actually considering drilling out the air hole on the side of the base - That's what started this...... now I'm not sure thats a good idea.
No flooding per se, but obviously something is going on.... I guess the airtube was preventing that sound. I've tried blowing thru the air hole from the outside, I don't hear any fluid being pushed or anything.
I'm a little lost here. I was actually considering drilling out the air hole on the side of the base - That's what started this...... now I'm not sure thats a good idea.
Just a thought here maybe, is your coil so close to the air hole that juice "hanging" on the bottom of the coil is trying to block it?
You'll need to increase the airways on the Taifun for dripper like characteristics, perhaps a Fogger v4 would be better suited for your style of vaping.
No.... and I can't figure out where the liquid is slurping from... there is no juice leaking, none in the drip tip.
If I hold it upside down, it'll stop for a few puffs, then comes back.
All my air tubes are pulled out... I do 8-10 wraps of 26ga kanthal around a 3/32" mandrel.. ends up about 1 ohm. Torched and compressed before wicking. Cotton wick that's a little more than enough to fill the coil... Enough to still be able to slide the cotton with some ease, but not flopping around in the hole. Which seems to be the perfect size to fill the slots on the sleeve without allowing it to flood. Also cut about 2mm from the sleeve which allows the wick to touch the sides of the tank which seems to allow me to completely empty the tank without burning the cotton when the juice level gets below the wick.
I run 13 watts on all my DNA devices with Taifuns on them. Gives me an absolutely perfect vape, as long as I'm doing mouth hits as the air draw isn't enough for lung hits without breaking a blood vessel... As I use these at work for stealth vaping, I am absolutely NOT looking for plumes of vapor...
I run 13 watts on all my DNA devices with Taifuns on them. Gives me an absolutely perfect vape, as long as I'm doing mouth hits as the air draw isn't enough for lung hits without breaking a blood vessel... As I use these at work for stealth vaping, I am absolutely NOT looking for plumes of vapor...
Last edited:
- Status
Similar threads
- Locked
