The FastTech Thread for All FastTech Posts (Part 2)

[WarHawk-AVG]

RMA is in finally
$3.48 Coil Heads for ST-10 Clearomizer (5-Pack) 5-pack - 2.4ohm at FastTech - Worldwide Free Shipping

The above go in
http://www.fasttech.com/products/1411/10006893/1549201 [which look like they would also work on the "gripper"

That I got for my wife (weird that the single pack x2 costs less than the double pack!!!!)

Original shipment..they sent me a stainless driptip, opened ticket..they immediately shipped the right ones (let me keep the ~$2 drip tip [that actually looks pretty good on my AGA-T2]..just got em...try that with ebay

Looks like FT got a buncha "flashlights" on the New Arrivals too!

 

[boomerdude]

Just markin' my territory. Carry on.

 

[Ladiekali]

RMA is in finally
$3.48 Coil Heads for ST-10 Clearomizer (5-Pack) 5-pack - 2.4ohm at FastTech - Worldwide Free Shipping

The above go in
$9.56 ST-10 310mAh Rechargeable Starter Kit - 2.4ohm / 1.0mL / USB charging cable at FastTech - Worldwide Free Shipping [which look like they would also work on the "gripper"

That I got for my wife (weird that the single pack x2 costs less than the double pack!!!!)

Original shipment..they sent me a stainless driptip, opened ticket..they immediately shipped the right ones (let me keep the ~$2 drip tip [that actually looks pretty good on my AGA-T2]..just got em...try that with ebay

Looks like FT got a buncha "flashlights" on the New Arrivals too!

Those are esmart clones? I need that topper if it is that small!

 

[WarHawk-AVG]

Those are esmart clones? I need that topper if it is that small!

sure look like it
Kangertech Esmart Black electronic cigarette

The tank on the ST-10 don't have the graduations like on the esmart though (and they are 510 threaded)
I'll post pics when I get home from work
Maybe this would allow you to put the ST-10 topper on an esmart battery
http://www.fasttech.com/products/1411/10003955/1563100

These appear to be 510 threaded (and appear to be top coil similar to a vivi nova mini)
http://www.ebay.com/itm/like/310854989947?lpid=82

 

[Ladiekali]

Im lookimg for a bottom coil for the 510 esmart...
Its an odd sized battery tho, bigger than a 510 cigalike.
Was thinking of trying a mini nano.

 

[boborone]

The above go in
$9.56 ST-10 310mAh Rechargeable Starter Kit - 2.4ohm / 1.0mL / USB charging cable at FastTech - Worldwide Free Shipping [which look like they would also work on the "gripper"

Nah, the gripper just fits a carto. Has to be a 44mm or larger carto, too.

 

[WarHawk-AVG]

Nah, the gripper just fits a carto. Has to be a 44mm or larger carto, too.

Tall

diameter wise it's 9-11mm in diameter (I believe cigalikes and associated cartos are 9.2mm diameter), the eGo is 14mm diameter

 

[Exile]

I have 4 different orders coming in from FT, and all of them have been constantly showing "shipping activity" every couple days.

1 - Shipped on 1/17 is now in California on my way to me in the next few days hopefully.
2 - Shipped on 1/19 is now in the US "preparing shipment".
3 - Shipped on 1/24 is now in the US "preparing shipment".
4 - Shipped on 1/25 is now in the US "preparing shipment".

http://www.17track.net/index_en.shtml

 

[Schnarph]

I have 4 different orders coming in from FT, and all of them have been constantly showing "shipping activity" every couple days.

1 - Shipped on 1/17 is now in California on my way to me in the next few days hopefully.
2 - Shipped on 1/19 is now in the US "preparing shipment".
3 - Shipped on 1/24 is now in the US "preparing shipment".
4 - Shipped on 1/25 is now in the US "preparing shipment".

http://www.17track.net/index_en.shtml

I don't care what's in those packages, I'm jealous.
http://www.17track.net/en/result/post.shtml?nums=RE663682298SE "shipped" 1/7, last seen 1/14
http://www.17track.net/en/result/post.shtml?nums=LK048741602HK "shipped" 1/20, not found

 

[Exile]

I have 4 different orders coming in from FT, and all of them have been constantly showing "shipping activity" every couple days.

1 - Shipped on 1/17 is now in California on my way to me in the next few days hopefully.
2 - Shipped on 1/19 is now in the US "preparing shipment".
3 - Shipped on 1/24 is now in the US "preparing shipment".
4 - Shipped on 1/25 is now in the US "preparing shipment".

http://www.17track.net/index_en.shtml

I don't care what's in those packages, I'm jealous.

Mainly just a bunch of different RDA's....

1 - https://www.fasttech.com/p/1451809
https://www.fasttech.com/products/0/10004437/1452201-v5-rda-rebuildable-dripping-atomizer

2 - https://www.fasttech.com/p/1439600
https://www.fasttech.com/p/1604700

3 - https://www.fasttech.com/p/1573500
https://www.fasttech.com/products/0/10005256/1418702-trident-stainless-steel-rebuildable-atomizer
https://www.fasttech.com/p/1603000

4 - https://www.fasttech.com/p/1437023
https://www.fasttech.com/p/1422703

 

[Burnie]

Mainly just a bunch of different RDA's....

1 - $8.50 Trishula Round Mouth Atomizer (2.0mL) at FastTech - Worldwide Free Shipping
$5.32 V5 RDA Rebuildable Dripping Atomizer - 1*airhole / laser etched logo at FastTech - Worldwide Free Shipping

2 - $5.93 V12 Rebuildable Dripping Atomizer at FastTech - Worldwide Free Shipping
$6.07 Patriot Style Rebuildable Dripping Atomizer - 22mm diameter at FastTech - Worldwide Free Shipping

3 - $5.43 Patriot Style Rebuildable Dripping Atomizer at FastTech - Worldwide Free Shipping
$12.06 Trident Stainless Steel Rebuildable Atomizer at FastTech - Worldwide Free Shipping
$6.66 Omega Style Rebuildable Dripping Atomizer at FastTech - Worldwide Free Shipping

4 - $8.30 Mini Protank E-Cigarette Atomizer (1.5mL) - translucent / 2.5ohm / removable drip tip / 2*coil head at FastTech - Worldwide Free Shipping
$11.06 EGO-C Twist 650mAh Variable Voltage Rechargeable Battery for E-Cigarette - silver / 3.2-4.8V at FastTech - Worldwide Free Shipping

There I fixed your links for you. Faster than clicking on them to see what they are.

Vape On
Burnie

 

[Maggiemw]

To add to my Kayfun obsession-collection, I've just received this: $5.12 Spare Parts for Kayfun v3.1 Atomizer - PMMA . I've been playing mix and match with it and my Kayfun 3.1 since yesterday. I'm very pleased with how the sections fit the 3.1. The threading is fine, the O-rings are effective, the look is very different and fun, and the whole 3.1 is a lot lighter in weight. The performance is no different - just as smooth and excellent.

Haven't tried the whole set on the Lite yet, but that will come eventually.

 

[puchox]

To add to my Kayfun obsession-collection, I've just received this: $5.12 Spare Parts for Kayfun v3.1 Atomizer - PMMA . I've been playing mix and match with it and my Kayfun 3.1 since yesterday. I'm very pleased with how the sections fit the 3.1. The threading is fine, the O-rings are effective, the look is very different and fun, and the whole 3.1 is a lot lighter in weight. The performance is no different - just as smooth and excellent.

Haven't tried the whole set on the Lite yet, but that will come eventually.

Never crossed my mind using the pmma parts to lower the weight of the 2 KF + 2 MVP in my pocket when i'm outside :/ I have some shopping to do after the chinese holidays

 

[JBR3AK]

I'm not sure what you mean by "adjustable sleeve", but the contact pin isn't really adjustable. I put a tiny o-ring near the bottom of the center pin to get some extra length needed for a hybrid kit, but it's a one piece, hollow pin from the 510 connector to the top of the deck where it screws into the rectangular positive block. Pizzpoor center pin design compared to the $21.54 SvoeMesto Kayfun v3.1 ES Styled Rebuildable Atomizer (4.5mL) - stainless steel at FastTech - Worldwide Free Shipping since the $26.70 Russian 91% Styled Rebuildable Atomizer (4.5mL) at FastTech - Worldwide Free Shipping has a hollow center pin that is easy to break, but the Kayfun 3.1 ES also needed a tiny o-ring at the bottom of the center pin to keep from shorting against the outside of the 510 connection (negative). At least the pin is adjustable on the 3.1. Also I didn't have to do anything to stop the whistle of the 3.1, the 91% took some work. The 91% is easier to fill though, I guess they both have good and bad features.

I'm just asking since my brother got the "authentic" R91%. The provari won't make the connection if you tighten it down right out of the box. I took it all apart to see what the "OP" error was all about. Here, the center pin looked like a long screw that just went to the positive rectangle block. In the middle, there was a o-ring squished. I backed out the center pin from that "center pin sleeve", rebuilt it, and viola. My concern is, I'll run into the same problem if the center pin (not the sleeve) isn't adjustable. If the connector pin IS one long solid piece on the tobecco, and I have to adjust it, that positive rectangle piece will slop around like a party favor. I'm just praying it works as is out of the box and I won't need any adapters to run it. I'd stick to my PT2 with the same issue if that's the case. it's a clone of a clone after all..

Now, I'm lead to a new question.. Is the FT R91% a 1:1 fit with the centerpin of the original R91%?


Sent from my Provari v2.5 using Tapatalk

 

[Schnarph]

I'm just asking since my brother got the "authentic" R91%. The provari won't make the connection if you tighten it down right out of the box. I took it all apart to see what the "OP" error was all about. Here, the center pin looked like a long screw that just went to the positive rectangle block. In the middle, there was a o-ring squished. I backed out the center pin from that "center pin sleeve", rebuilt it, and viola. My concern is, I'll run into the same problem if the center pin (not the sleeve) isn't adjustable. If the connector pin IS one long solid piece on the tobecco, and I have to adjust it, that positive rectangle piece will slop around like a party favor. I'm just praying it works as is out of the box and I won't need any adapters to run it. I'd stick to my PT2 with the same issue if that's the case. it's a clone of a clone after all..

Now, I'm lead to a new question.. Is the FT R91% a 1:1 fit with the centerpin of the original R91%?


Sent from my Provari v2.5 using Tapatalk

It will indeed spin around like a party favor, which is why I put a tiny o-ring at the bottom of the center pin. This way, you have about 1/2 turn of adjustment while maintaining pressure at the top with the rectangular positive block. If you don't have the right o-ring, cutting a ring from a Protank head grommet should work. I used a sliver cut from an AGA-T center pin insulator, nice and squishy silicone.

I had an authentic R91 V2 but sold it without checking if any parts are interchangeable. They should be, but obviously it's not a 1:1. The FT "R91" is more of a KFL + (KFL with airflow control).


This kit $5.12 Spare Parts for Kayfun v3.1 Atomizer - PMMA at FastTech - Worldwide Free Shipping is nice isn't it? The weight difference is substantial. I wish the main tube was straight instead of rounded, but it is much cheaper than the straight ones found elsewhere. The clear chimney is kinda gross. It doesn't do anything to the flavor, but I didn't need to see my cotton wick go black that fast, less than one tank and it was icky in there.

 

[JBR3AK]

It will indeed spin around like a party favor, which is why I put a tiny o-ring at the bottom of the center pin. This way, you have about 1/2 turn of adjustment while maintaining pressure at the top with the rectangular positive block. If you don't have the right o-ring, cutting a ring from a Protank head grommet should work. I used a sliver cut from an AGA-T center pin insulator, nice and squishy silicone.

I had an authentic R91 V2 but sold it without checking if any parts are interchangeable. They should be, but obviously it's not a 1:1. The FT "R91" is more of a KFL + (KFL with airflow control).


This kit $5.12 Spare Parts for Kayfun v3.1 Atomizer - PMMA at FastTech - Worldwide Free Shipping is nice isn't it? The weight difference is substantial. I wish the main tube was straight instead of rounded, but it is much cheaper than the straight ones found elsewhere. The clear chimney is kinda gross. It doesn't do anything to the flavor, but I didn't need to see my cotton wick go black that fast, less than one tank and it was icky in there.

Thanks for the heads up. I plan on running JC Tundra (most likley a bad choice of juice to run in it). I expect the cotton and coukd to looking charcoal after 13 vapes.. Any tips for running the red oak line in it, or just keep dripping it in my HH357 atty?


Sent from my Provari v2.5 using Tapatalk

 

[Myrany]

Nah, the gripper just fits a carto. Has to be a 44mm or larger carto, too.

Actually there is an extension you can get from mad vapes that lets you put anything 510 on it which is how I use it with my Squid.

 

[Schnarph]

Thanks for the heads up. I plan on running JC Tundra (most likley a bad choice of juice to run in it). I expect the cotton and coukd to looking charcoal after 13 vapes.. Any tips for running the red oak line in it, or just keep dripping it in my HH357 atty?


Sent from my Provari v2.5 using Tapatalk

Do what you like, but the clear chimney in the $5.12 Spare Parts for Kayfun v3.1 Atomizer - PMMA at FastTech - Worldwide Free Shipping lets you see a icky, burnt coil and cotton if you use sweet, high VG juice like I do. In a way, it's a bonus, you can see when it's time to clean it rather than taste it. The clear tank and top cap are great and lightweight, I just kept the SS chimney that came with the KFL+/R91%/whatever it's called:

Still searching for a clear, frosted tip to put on this beauty. Vamo also from FT, split kit from some crazy Belgian.

Edit: that's not the clear tank from FT, just the top cap. I have the slightly round clear tank tube on my other FT Kayfun (3.1 ES).

 

[soupy1970]

Got my black box Aqua today $20.00 Aqua Style Rebuildable Atomizer - 2*drip tips / hybrid connector pin at FastTech - Worldwide Free Shipping . Shipping took 5 days from FT to Chicago, then 6 days to process through Chicago and travel 5-6 hours down state to me.

I am new to Rebuildables having only tinkered with the Trident and Helios clones over the last 2 weeks. I have a Kayfun 3.1 on it's way $21.54 SvoeMesto Kayfun v3.1 ES Styled Rebuildable Atomizer (4.5mL) - stainless steel at FastTech - Worldwide Free Shipping .

So far I am digging this thing a lot! It was easy to build (dual coil mode), and really blows some clouds. I have only vaped it on my Evic & MVP 2 at 1.7 ohms on 11 watts (first build) so far. Tomorrow I will probably rebuild it to around 0.8, and try it out on my Nemeisis Mix Mod (still getting the hang of that too). I kinda dove right in and am very new to vaping still, (since Nov. 12) but the Aqua gets my approval.

Just a little bit of leaking at first but it worked itself out right away.

 

[WarHawk-AVG]

Got a new toy in today ($7 gripper from madvapes)

These fit in em PERFECTLY with about 1/2" of the drip tip sticking out, vaping like a mad dog, have gone thru 1-1ml tank already and the 18350 battery is STILL chugging along! (checked the volts on a multimeter, 3.89vdc after first tank)

$1.71 EGO 510-T Electronic Cigarettes Flat Mouth Atomizer with Refill - black at FastTech - Worldwide Free Shipping

Soooooo ready to stealth vape this little monster!