Deleting my own post. Hoping to remove faulty pic...
Attachments
Last edited:
- Status
I also would like to share...
I have these clearos and they are rhe only ones i use. They are awesome.
Small size but work like a champ, much better than all the other clearos i have...
Iclear 16, kanger t3, evod etc.....
https://www.fasttech.com/products/1424404
I have these clearos and they are rhe only ones i use. They are awesome.
Small size but work like a champ, much better than all the other clearos i have...
Iclear 16, kanger t3, evod etc.....
https://www.fasttech.com/products/1424404
I got one of these to see what the were like (I kinda like the pinky fire button [I have a "The Natural" I won on FB])
Plus it's 21mm and I don't think the Caravella genesis (I-Atty clone) will match up with Caravela mod 22mm [well once I fix the 510 connector]...fooey)
https://www.fasttech.com/products/1391600
Last edited:
Just ordered cheap ohm volt meter.
$11.49 Volt Ohm Meter for E-Cigarette at FastTech - Worldwide Free Shipping
I'm very interesting how accurate it is..?
$11.49 Volt Ohm Meter for E-Cigarette at FastTech - Worldwide Free Shipping
I'm very interesting how accurate it is..?
so FT drippers: i suggest everyone buy 10 of these cause they are AWESOME. easy to setup great performers and very cheap.
they do have some problems. the main problem is the negative post which is press fitted and after some use tends to come loose and cause resistance jumps.
the easiest to setup from my latest batch was this one https://www.fasttech.com/p/1483904 . it has an aluminum top cap but other than that is very good.
they best perform in mechs at about 0.8-1.2 ohms. so if you want to try dripping and don't want to spend a lot of money, you can't go wrong with these.
they do have some problems. the main problem is the negative post which is press fitted and after some use tends to come loose and cause resistance jumps.
the easiest to setup from my latest batch was this one https://www.fasttech.com/p/1483904 . it has an aluminum top cap but other than that is very good.
they best perform in mechs at about 0.8-1.2 ohms. so if you want to try dripping and don't want to spend a lot of money, you can't go wrong with these.
Pretty accurate...when I short it, it/s within .14 ohms, so just offset the reading from the coil by the drift amount.
Make sure you keep it clean when reading resistance...a little bit of juice can change the reading
I am so excited! My stuff is in the US.
2014-01-10 13:08, Processed Through Sort Facility, ISC CHICAGO IL (USPS)
, Origin Post is Preparing Shipment
2014-01-08 09:47, Processed Through Sort Facility, SHENZHEN EMS, CHINA
2014-01-07 14:56, Acceptance, CHINA
2014-01-10 13:08, Processed Through Sort Facility, ISC CHICAGO IL (USPS)
, Origin Post is Preparing Shipment
2014-01-08 09:47, Processed Through Sort Facility, SHENZHEN EMS, CHINA
2014-01-07 14:56, Acceptance, CHINA
My stuff is almost here!
Shipment Activity Location Date & Time
-------------------------------------------------------------------------------------------------------------------
Processed Through Sort Facility ISC CHICAGO IL (USPS) January 11, 2014 11:17 am
Origin Post is Preparing Shipment
Processed Through Sort Facility SHENZHEN EMS, CHINA January 9, 2014 10:24 am
Acceptance CHINA January 8, 2014 5:42 pm
Shipment Activity Location Date & Time
-------------------------------------------------------------------------------------------------------------------
Processed Through Sort Facility ISC CHICAGO IL (USPS) January 11, 2014 11:17 am
Origin Post is Preparing Shipment
Processed Through Sort Facility SHENZHEN EMS, CHINA January 9, 2014 10:24 am
Acceptance CHINA January 8, 2014 5:42 pm
Place order 1/4. Just checked status and it says order received 1/12...what 8 days..and it isn't even shipped yet. I do not know if it could have been held up for an item out of stock or what but when I placed the order I did not notice that any items were out of stock.
My whole order waited on the brass nemesis clone. It said in stock, until I placed the order, then it changed to: "expected ship date:" status on that one item. Thankfully, the order shipped 3 days ( including the brass nemmy) earlier than the "expected" ship date.
Looking at it I'd say your 100% correct. Unfortunately there's no air coming up even with multiple tries with different batteries and coil changes. POC no matter how you look at it. Air travels through to the mouthpiece slightly unconnected but even screwed down to a light touch cuts off the air travel. The air path is not blocked from the mouthpiece down to the coil. I think the coil base is too wide for the air to get fully past the coil assembly to the hole in the coil base.
Glad I only got one.
Glad I only got one.
Haven't studied 510 connections much have you?
Air Passes through the Side Holes, Travels DOWN to the OPEN Center pin and Back up through the Atomizer.
However If you over tighten, you can smash the center pin grommet and block the air channel.
If you Flush mount, the base is flat, you will cut off air flow.
Some Mods are notorious for blocking Air paths on certain tank designs.
Welcome to the world of Vaping
Update on my new Gripper/Pipe mod:
- It's a good, solid mechanical mod. It works great.
- The blue sleeve that comes with it screws onto it's eGo threads for when I want to use something skinny like a cartomizer.
- With the blue sleeve taken off, I can fit a CE5, mini Vivi Nova, EVOD, or T2 just fine and still use it folded up like a Gripper.
- Bigger toppers can be used, but only in Pipe mode, not in Gripper mode.
I haven't had a chance to play with in 18650 mode yet. I'm waiting until I get a really long drip for that.
X2 If I go with replaceable batteries, this is going to be the straw that breaks it.
Just curious. Off the mod, does it have a smooth draw? Should because that would be straight center pin opening Up. If tight, the coils may be packed to tight.
Also, easy enough to look for gap coil to 510 under decent light.
Tank itself is probably fine. 510 is 510 and if it screws on, the bore should be correct. Check for clear open 510 holes with wick off base also.(No slag in holes)
Hope you find something simple. Tank looks interesting.
Any one have a link to a decent ego battery from ft? Looking to put together some kits for friends but i dont use egos!
Theres too many to chose from. Not looking for a kit, just the battery
Theres too many to chose from. Not looking for a kit, just the battery
- Status
Similar threads
- Locked
